Schweitzer Engineering Laboratories SEL-734W Скачать руководство пользователя страница 9

Страница: 9 / 48

Date Code 20191029

Field Reference Guide

SEL-734W and SEL Wireless Current Sensor

Instruction Manual

Preface

Overview

The SEL-734W Capacitor Bank Control is based on the SEL-734 Advanced
Metering System platform. Devices ship with an outdoor-rated enclosure and are
programmed with control strategies via SEL design templates.

The

SEL-734W Field Reference Guide

provides a general overview of the

SEL-734W and describes the procedures for installation as a capacitor bank con-
trol. This guide also provides troubleshooting and testing methods.

The

SEL-734W Data Sheet

describes the SEL-734W and SEL-WCS system, the

features and control strategies of the SEL-734W, as well as interface.

The

SEL-734W

SEL

ERATOR

QuickSet Design Template Guide

describes the

operation, details the settings, and contains logical diagrams for developers.

The

SEL-734 Instruction Manual

details all other features available in the

SEL-734 device, including metering, power quality, and communications.

Safety Information

Dangers, Warnings, and Cautions

This manual uses three kinds of hazard statements, defined as follows:

Safety Symbols

The following symbols are often marked on SEL products.

DANGER

Indicates an imminently hazardous situation
that, if not avoided,

will

result in death or seri-

ous injury.

WARNING

Indicates a potentially hazardous situation
that, if not avoided,

could

result in death or seri-

ous injury.

CAUTION

Indicates a potentially hazardous situation
that, if not avoided,

may

result in minor or mod-

erate injury or equipment damage.

CAUTION

Refer to accompanying documents.

ATTENTION

Se reporter à la documentation.

Earth (ground)

Terre

Protective earth (ground)

Terre de protection

Содержание SEL-734W

















































Результаты поиска

Содержание SEL-734W

Отзывы:

Похожие инструкции для SEL-734W

Бренды по названию

Популярные бренды

Schweitzer Engineering Laboratories SEL-734W, Справочник по полевым условиям эксплуатации

Результаты поиска

Содержание SEL-734W

Отзывы:

Похожие инструкции для SEL-734W

Бренды по названию

Популярные бренды