background image

Page 4

2. Your Safety

This appliance is not intended for use by person/s (including children) with reduced physical, sensory or 
mental capabilities, or lack of experience and/or knowledge. Unless the person has been given supervision 
or instruction concerning the use of the appliance by a person responsible for their safety. Children should be 
supervised to ensure that they do not play with the appliance, it is not a toy.

Do not install Isodrive motor to a non-Schweigen and/or non-silent rangehood. If you fail to do so, your 
warranty will be voided.

The manufacturer declines all responsibility in case of failure to adopt proper safety measures.

Ensure that the location in which this appliance is installed, has good and permanent ventilation.

Please consult local laws and regulations and install in accordance.

Use an electrical connector with earth that is correct for your location.

Check that the voltage in your area corresponds to the appliance as indicated on the rating label.

Before Installation

We recommend this appliance to be installed or repaired by a qualified Schweigen Home Appliances technician. 

Please see our website 

www.schweigen.com.au

 for recommended installers.

It is dangerous to modify any part of this appliance. Modification of any kind, will immediately void the warranty.

Electrical Cord

Ensure the supply cord is not exposed to heat, chemicals or sharp objects. If the supply cord is damaged, it must be 
replaced by the manufacturer, service agent or a similarly qualified person in order to avoid a hazard. The power 
supply cord connection 

MUST BE

 installed in such a way that access is easy in case of emergency.

RECEIVING YOUR RANGEHOOD

Please read this section thoroughly before attempting to operate the appliance. 
Inspect your product upon receipt. 

Any damage or defects MUST be reported 

within 48 hours, or no claim will be recognised.

DO NOT INSTALL THIS APPLIANCE IF YOU FIND IT DAMAGED.

If this product is installed damaged, the supplier, nor the retailer, will be responsible 
for the costs associated with the repair, replacement, removal or re-installation of 
the appliances.

Содержание Isodrive 900





























Отзывы: