manualshive.com logo in svg

Schulte FX-520, Руководство оператора, Страница: 78 / 166

Поделиться
Скачать
Schulte FX-520 Скачать руководство пользователя страница 78

OPERATION

FX-520   06/16

Operation Section 4-24

© 2016 Alamo Group Inc.

OPERA

T

ION

Operating the mower with loose blade hardware will damage the blade holder or blades and
can result in blade breakage or blade fastener failure. Broken blades or bolts can be thrown
out from under the mower for distances up to 300 feet. When the blades are replaced, the
fastening hardware must be replaced. Check and retighten the blade hardware after the first
eight hours of operation. In severe cutting conditions, recheck the blade carrier and blade
bolt torque every 50 hours.

To help prevent structural damage caused by loose hardware, tighten gearbox mounting
hardware as specified. Check the fastener torque after first 8 hours of use and every 50
hours thereafter.

Inspect the Blades daily for abnormal wear. REPLACE BOTH BLADES on that carrier
IMMEDIATELY if either blade has:

•

Become bent or deformed from it’s original shape or

•

Any cracks are visible, or 

•

Deep gouges in the blade’s surface are present, or

•

Gouges or chipped areas in the cutting edge are larger than 1/2” (12.7mm), or 

•

The material on the leading edge has been worn away by more than 1/2” (12.7mm)”

Failure to replace abnormally worn blades may lead to catastrophic failure of the blades and ejection of the
broken part with tremendous force which may cause serious bodily injury or death. 

OPS-U-0032

Содержание FX-520







































































































































































Отзывы:

Нет отзывов