Schonstedt Instrument TraceMaster Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 17

Schonstedt Instrument TraceMaster Скачать руководство пользователя страница 16

SECTION VII: SONDE OPERATION

(You must have a Schonstedt Sonde for this option)

Introduction

If your TraceMaster unit is fitted with the sonde option then it supports the detection of of one or more of
thses sondes:

- Schonstedt's 512 Hz sonde
- 512 Hz sondes from any other manufacturer
- Schonstedt's 82 kHz sonde

These types of sondes are usually attached to devices that are sent through sewer pipes or water pipes. The
emmitted frequency penetratres the walls of such pipes.

Since the signal being traced by the receiver is produced by the sonde, and not travelling along the pipes,
there are some differences in the way the receiver is used. The following section explains how to use the
Tracemaster receiver for sonde operation.

Setting the Receiver for Sonde Mode

How you set your receiver for sonde operation will vary
slightly depending on whether you have purchased a
receiver-only unit or a complete TraceMaster unit
(receiver and transmitter). In both cases, you will know
you are in the sonde mode because the dot next to the
"PASSIVE" and the dot next to another frequency legend
on the display will BOTH be lit, as shown in the figure
below. The frequency legend with a dot next to it will
either be 575 Hz (for a 512 Hz sonde) or 82 kHz (for an
82 kHz sonde).

Receiver Only Unit or Receiver Without RF Link

If your TraceMaster is a "Passive Only", or "P 1 active Frequency", pressing the "FREQ" button
will cycle through the "Passive" mode, "Sonde" modes and the single frequency (if present). That simple!

Receiver with Transmitter and Multiple Frequencies

To use the sonde mode, first make sure the RF link is disabled--(see page 15). If the RF link is not disabled
you can still access the sonde mode(s), even if the transmitter is off, but you will not be able to then switch
to another active frequency or the passive mode, if the transmitter remains off. Access the sonde mode by
pressing the "FREQ" switch a few times, until the dots next to the "Passive" and the "575 Hz" legends on
the display are

BOTH

lit.

NOTE: Make sure to re-enable the RF link when you are finished with the Sonde Mode.

«
...
14
15
16
17
»

Содержание TraceMaster


















Отзывы:

Нет отзывов