SCHOLTES SR11PSWAA, Руководство по эксплуатации

Страница: 4 / 32

GB
4
Connecting the gas supply Connecting the gas supply Connecting the gas supply Connecting the gas supply Connecting the gas supply
To make the connection, a flexible hose should be used
corresponding to the current gas regulations which are:
• the hose must never be at any point in its lenght in
contact with the “hot” parts of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or torsional
stress and it must not have any excessively narrow
curves or bottlenecks;
• the hose must be easy to inspect along its entire
length to check its condition;
• the hose must always be in good condition, never
attempt to repair.
Important: Important:
Important: Important:
Important:
the installation must comply with gas safety
(installation and use) regulations 1984. In all cases for
the above, by low, a qualified, corgi approved engineer
must be called for installation.
Disposing of the appliance Disposing of the appliance Disposing of the appliance Disposing of the appliance Disposing of the appliance
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the
plug body and dispose of it as described above.
Adapting the cooker to different types of gas Adapting the cooker to different types of gas Adapting the cooker to different types of gas Adapting the cooker to different types of gas Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of gas
with respect to the gas for which it was produced
(indicated on the label attached to the lid), follow these
steps:
a) a) a) a) a)
replace the hose holder mounted on the appliance
with that supplied in the bag of “cooker
accessories”.
b) b)
b) b)
b)
Replacing the burner nozzles on the hob:
• remove the grids and slide the burners from their
housings;
• unscrew the nozzles using a 7 mm socket spanner,
and replace them with nozzles for the new type of
gas (see table 1 “Burner and nozzle characteristics”).
• replace all the components by repeating the steps
in reverse order.
c) c) c) c) c)
Replacing the nozzles on separate “double crown
wok“ burners:
• remove the pan supports and slide the burners from
their housings. The burner consists of 2 separate
parts (
see below);
• unscrew the burers with a 7 mm wrench spanner.
The internal burner has a nozzle, the external burner
has two (of the same size). Replace the nozzle with
models suited to the new type of gas (see table 1).
• replace all the components by repeating the steps
in reverse order.
N.B.: N.B.: N.B.: N.B.: N.B.:
Conditions relating to the adjustment of this
appliance are listed on the label
d) d)
d) d)
d)
Minimum regulation of the hob burners:
• turn the tap to minimum;
• remove the knob and adjust the regulation screw,
which is positioned in or next to the tap pin, until
the flame is small but steady.
N.B.: N.B.:
N.B.: N.B.: N.B.:
in the case of liquid gas, the regulation screw
must be screwed in to the bottom.
• check that the flame does not turn off when you
turn the tap quickly from high to low.
e) e) e) e) e)
Regulating the primary air of the burners:
The primary air of the burners requires no regulation.
Important Important
Important Important
Important
On completion of the operation, replace the old rating
sticker with one indicating the new type of gas used.
This sticker is available from our Service Centres.
Note Note
Note Note Note
Should the pressure of the gas used be different (or
vary) from the recommended pressure, it is necessary
to fit a suitable pressure regulator onto the inlet pipe
in compliance with current National Regulations relati-
ve to “regulators for channelled gas”.