manualshive.com logo in svg

Schneeberger MINIRAIL, Руководство пользователя

Поделиться
Скачать
Schneeberger MINIRAIL Скачать руководство пользователя страница 33

33

10

 MINISCALE PLUS Error Description 

Error 

Possible Causes 

Solution

Resolution is not 
achieved

Visible interference 
in the measurement 
signal

Further errors

Interpolation too low

Evaluation too low

Incorrect input frequency

Incorrect customer-supplied 
cable

Further investigation needed

Maximum speed of 3.2 m/s 
exceeded

The number on the interface 
module does not match the 
MINISCALE PLUS carriage 
number

The number on the interface 
module does not match the 
MINISCALE PLUS carriage 
number

Increase interpolation

Contact SCHNEEBERGER

Adjust frequency to travelling 
speed

Limit the speed to 3.2 m/s 

Use digital interface module 
and digital input of the USB 
counter (caution: maximum 
speed 0.2 m/s)

For higher speeds, use the 
analog interface module and 
analog input (caution: maxi-
mum resolution 0.39 µm)

Check number relationship 
between interface module, 
carriages and guideways

Use a shielded twisted pair 
cable

System must be returned to 
SCHNEEBERGER for 
adjustment

Adjust as described in 
chapter 6.1  

Return the system to 
SCHNEEBERGER

Repeat evaluation 4 times

Digital interface 
module is not 
working correctly

Analog interface 
module is not 
working correctly

If using USB counter: Interpola-
tor has a resolution of just 256, 
meaning the displayable 
resolution is limited to 0.39 µm.

Digital input has a maximum 
input frequency of 500 kHz. 
The speed is therefore limited 
to 0.2 m/s (or 0.4 m/s) for a 
resolution of 0.1 µm. 

Incorrect position 
during high speeds 
when using USB 
counter

10  MINISCALE PLUS Err

or Description

www.servo2go.com

[email protected]

www.servo2go.com

Toll Free Phone: 877-378-0240

Toll Free Fax: 877-378-0249

[email protected]

www.servo2go.com

Sold & Serviced By:

Содержание MINIRAIL




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды