manualshive.com logo in svg

Schneeberger MINIRAIL, Руководство пользователя

Поделиться
Скачать
Schneeberger MINIRAIL Скачать руководство пользователя страница 16

16

5

 

 

 Installation and Adjustment Guidelines  

Open ZIF connector (H)

Insert the flexible printed circuit board (C) into the ZIF connector (H) 
of the interface module (F) without touching the gold contact points 
on the printed circuit board.

Make sure that the contact surfaces of the flexible 
printed circuit board are facing upwards so that 
contact is ensured.

Once the flexible printed circuit board has been inserted, push the 
ZIF connector towards it.

Once the sensor is connected to the interface module, which is 
connected to the grounded machine, it is protected from ESD and 
can be touched without ESD protection.

The flexible printed circuit board between the sensor and the 
interface module can only be used statically. The bending radius of 
the flexible printed circuit board must not fall below 2 mm.

www.servo2go.com

[email protected]

www.servo2go.com

Toll Free Phone: 877-378-0240

Toll Free Fax: 877-378-0249

[email protected]

www.servo2go.com

Sold & Serviced By:

Содержание MINIRAIL




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды