Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 63

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 62

DISMANTLING AND DISPOSAL

62 | EN

www.schmalz.com

30.30.01.00226/03

9

Dismantling and disposal

9.1 Dismantling

Read section 1.8 (Requirements and instructions for installation, maintenance
and operating staff) before dismantling. Observe the safety instructions in
sections 5 & 8 (Installation and maintenance).

Procedure:



Switch off the vacuum supply, depressurizing the compressed air line if applicable. Have electrical
lines disconnected by qualified personnel and secured to prevent the supply being switched back
on.



When dismantling the hoist, please observe the manufacturer's operating instructions.



Take down and disassemble the jib crane's lines and hoses.



Remove the sealing plates of the crane girder. When continuing to use the jib crane, ensure that
the crane rail is not damaged. The sealing plates have to be procured again in this case.



Remove fixed and variable end stops, take the cable trolley and transport trolley out of the crane
jib, release the terminal clamps and push out.



Support the crane jib with a suitable lifting aid.



Undo the connection to the crane column or wall bracket and bring this down to a safe level from
the floor. For reuse store this in a suitable base without damage.



Loosen the wall bracket and crane column screws and bring down safely to the floor or place the
crane column on the floor using a suitable lifting aid.



All components must be checked for damage and wear prior to reuse.



In Germany, a re-assembled jib crane requires renewed approval by a crane expert. Observe the
country-specific laws and regulations in this regard.

9.2 Disposal

Only qualified specialist personal may prepare the crane system for disposal.

Procedure:



Detach the crane system



Dispose of the materials, unmixed, in accordance with local provisions.



The plastics from the sealing plates PA6 GF30 can be recycled.



The transport trolley rollers fall under waste code 20 01 06 relating to other plastics and
constitute a non-toxic, non-biodegradable and water-insoluble solid without any known harmful
effects for the environment. They can be recycled unmixed or, in accordance with local
provisions, disposed of with household waste.

For proper disposal, please contact a company specializing in the disposal of technical goods and
instruct the company to observe the applicable disposal and environmental regulations.
The manufacturer of the device will be happy to assist you in finding a suitable company.

«
...
60
61
62
63
»

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX
































































Отзывы:

Нет отзывов