Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 63

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 30

INSTALLATION

30 | EN

www.schmalz.com

30.30.01.00226/03

5

Installation

Installation must be performed only by qualified electrical and mechanical specialists (see section 1.8
Requirements and instructions for installation, maintenance and operating staff).

DANGER

Sources of ignition during installation

Risk of explosion

►

Ensure that a potentially explosive atmosphere is not produced during
installation.

An explosion protection representative commissioned by the operator must check and approve the
entire plant (the items included in the delivery from J. Schmalz GmbH and the customer-side
installation) in accordance with ATEX 1999/92 EC and the national regulations before the start of
operations.

WARNING

Danger due to parts with sharp edges and heavy components

There is a risk that you may cut yourself when installing the parts, these may
also fall or topple over thereby hitting and injuring people.

► Wear an industrial safety helmet (in accordance with EN 397)

► Wear work gloves (in accordance with EN 388 safety category 2133)

► Wear safety shoes (in accordance with EN 20345 safety class S1)

WARNING

Risk of injury due to falling parts or persons

This may result in serious injury

► When performing work on the jib crane, the entire crane area must be

cordoned off!

► When performing work on the jib crane an appropriate climbing aid, lifting

platform or fall prevention device must be used.

«
...
28
29
30
31
32
...
»

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX
































































Отзывы:

Нет отзывов