Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 12

Страница: 12 / 63

SAFETY INSTRUCTIONS

12 | EN

www.schmalz.com

30.30.01.00226/03

1.7 Non-intended use

The manufacturer accepts no liability for damages caused by the use of the jib crane for other
purposes. The use of the jib crane for loads that are not specified in the order confirmation or that
have different physical properties than those

specified in the order confirmation shall be considered

non-intended use.

WARNING

Non-intended use

Risk of fatal injuries

►

Usage in impermissible potentially explosive atmospheres (see chapter 1.6).

Usage as a climbing aid

Lifting living things

Storing a suspended load.

WARNING

Handling a load with more than one jib crane

Danger of fatal injuries due to falling objects

►

The load must be handled only with

one

jib crane.

The manufacturer must be consulted before handling a load using a
combination of more than one jib crane.

1.8 Requirements and instructions for installation, maintenance and

operating staff

DANGER

Errors during operation, maintenance or repair work

Risk of explosion

►

The operator must ensure that the personnel employed receive special
training for performing work in potentially explosive atmospheres.

Comply with the applicable national regulations.

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX
































































Результаты поиска

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX

Отзывы:

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Инструкция по эксплуатации и техническому обслуживанию, Страница: 12 / 63

Результаты поиска

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX

Отзывы: