Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Скачать руководство пользователя страница 59

Страница: 59 / 63

MAINTENANCE

30.30.01.00226

/03

www.schmalz.com

EN | 59

Maintenance

8.1 General notes

Read section 1.8 (Requirements and instructions for installation, maintenance
and operating staff) before starting maintenance work.

DANGER

Ignition sources during maintenance/repair work

Risk of explosion

►

Ensure that no potentially explosive atmosphere is produced during
maintenance/repair work.

Measure the resistance after all maintenance/repair work.

WARNING

Risk of injury due to system maintenance by untrained personnel

This may result in serious injury

►

The system may be maintained only by trained personnel who have read and
understood the operating and maintenance instructions.

WARNING

Risk of injury from worn, unmaintained parts

Worn and unmaintained parts can cause damage, resulting in failure of the
crane system and potentially causing severe injury.

► Observe the operating, maintenance and servicing requirements specified in

these operating instructions.

WARNING

Risk of injury due to falling parts or persons

This may result in serious injury

► When performing work on the jib crane, the entire installation must be

cordoned off!

►

When performing work on the jib crane an appropriate climbing aid, lifting
platform or fall prevention device must be used.

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX
































































Результаты поиска

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX

Отзывы:

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Инструкция по эксплуатации и техническому обслуживанию, Страница: 59 / 63

Результаты поиска

Содержание SK-JU-110-2000-SRS63-3000-VSL-EX

Отзывы: