background image

15

Lawnaire

IV 

with

 EST

STORAGE INSTRUCTIONS

 

To prevent possible explosion or ignition of vaporized 

fuel, do not store equipment with fuel in tank or 

carburetor in an enclosure with open flame (for 

example, a furnace or water heater pilot light).

Before the equipment is put into storage for any 

period exceeding 30 days, the following steps 

should be taken.

1.  Drain all fuel from the fuel tank and fuel lines.

2.  Start the engine and run until all the fuel is used 

from the carburetor float bowl.

3.  While the engine is still warm, drain the 

crankcase oil and refill with the proper weight oil 

corresponding to the season the equipment will 

next be used.

4.  Remove the spark plug and squirt a small 

amount of engine oil into the cylinder.  Turn the 

engine over a few times to distribute the oil.

5.  Drain the water drum.

NOTE

:  Always drain the water drum for winter 

storage.  Freezing water can rupture the drum.

6.  Grease the clutch pivot fitting, tine wheel and 

wheel bearings.

6.  Lubricate the chain.

To put the equipment into service after an 

extended period of storage:

1.  Check for loose parts and tighten if necessary.

2.  Check for cracked or broken tines and replace as 

necessary.

3.  Fill the fuel tank with clean, fresh fuel.

4.  Check the engine and gear reduction case oil 

levels with the engine in a level position.

5.  Start the engine.

6.  Check for fuel leaks.

7.  Check clutch control operation to make sure the 

unit stops when the clutch control is released. 

STORAGE

Содержание RYAN LAWNAIRE IV

































Отзывы: