Schiller Grounds Care BUNTON 642246F Скачать руководство пользователя страница 39

Страница: 39 / 40

BUNTON

MISSILE

PUMP-DRIVE BELT

1. Remove engine-cutterdeck belt (see engine-cutterdeck belt replacement).
2. Attach an extension to a 3/8" drive ratchet. Insert the ratchet extension in the square hole of the pump

drive idler arm. Use the ratchet handle to rotate it enough to remove the pump drive belt.

3. Install a new pump drive belt in the same manner as it was removed.
4. Re-install engine-cutterdeck belt (see engine-cutterdeck belt replacement).

CUTTERDECk BELT

1. Set the cutterdeck in the lowest height-of-cut

position.

2. Remove the engine-cutterdeck belt from the deck

idlers and pulley (see engine-cutterdeck belt

replacement). Push it aside but don't remove it

from the machine.

3. Run the cutterdeck belt off the idler as shown.

Remove it from the deck.

4. Install the new belt by performing these steps in

reverse order. Take care to get the new belt on

the correct side of the belt guides.

5. Re-install engine-cutterdeck belt (see engine-

cutterdeck belt replacement).

BELT REPLACEMENT

Содержание BUNTON 642246F









































Результаты поиска

Содержание BUNTON 642246F

Отзывы:

Похожие инструкции для BUNTON 642246F

Бренды по названию

Популярные бренды

Schiller Grounds Care BUNTON 642246F, Руководство оператора

Результаты поиска

Содержание BUNTON 642246F

Отзывы:

Похожие инструкции для BUNTON 642246F

Бренды по названию

Популярные бренды