Schiller Grounds Care BUNTON 642246F Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 40

background image

29

BUNTON

MISSILE

MAINTENANCE

ENGINE OIL

Do not perform engine maintenance without the

engine off, spark plug wires disconnected and PTO

disengaged.

AFTER FIRST FIVE (5) HOURS

While the engine is warm:
1. Remove drain cap

D

and drain the crankcase.

Dispose of used oil in accordance with local

requirements.

2. Clean and replace the cap.

3. Change oil filter.

4. Fill the crankcase with fresh oil to the full mark.

Do not overfill. See engine manual for oil

specifications.

DAILY

1. Check oil level with the dipstick.

2. If oil is needed, add fresh oil of proper

viscosity and grade. See engine manual for oil

specifications. Do not overfill.

3. Replace dipstick before starting engine.

PERIODIC OIL CHANGES

1. See engine manual for oil and filter change inter

-

vals after the break-in period.

2. Follow instructions for first oil change, above.

SPARk PLUGS

Remove each plug and check condition.
– Good operating conditions are indicated if the plug has a light coating of grey or tan deposit.
– A white blistered coating indicates overheating. A black coating indicates an “over rich” fuel mixture. Both

may be caused by a clogged air cleaner or improper carburetor adjustment.

– Do not sandblast, wire brush or otherwise attempt to repair a plug in poor condition. Best results are

obtained with a new plug.

– Set plug gap as specified in engine manual..

CLEANING MACHINE

Clean the machine after use. The machine will run cooler and last longer if kept free of clippings and other

debris. A clean machine also reduces the risk of fire due to accumulation of combustible debris and chaff

Brush or blow clippings and debris off the cutterdeck and engine deck.

«
...
29
30
31
32
33
...
»

Содержание BUNTON 642246F









































Отзывы:

Нет отзывов

Похожие инструкции для BUNTON 642246F

Бренд: Jacobsen Страницы: 108

Бренд: H&S Страницы: 32

532 43 45-09 Rev. 1

Бренд: McCulloch Страницы: 76

Бренд: Snapper Страницы: 40

Бренд: MTD Страницы: 24

Бренд: Poulan Pro Страницы: 56

Zero Turn Radius Mower

Бренд: Country Clipper Страницы: 25

ZT13536, ZT17542B, ZT20050

Бренд: Swisher Страницы: 28

Бренд: Yard-Man Страницы: 28

Бренд: ECLOZ Страницы: 56

Бренд: Kärcher Страницы: 17

Бренд: VITO GARDEN Страницы: 33

Бренд: Kubota Страницы: 117

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды