Schiller Grounds Care BUNTON 642246F Скачать руководство пользователя страница 30

Страница: 30 / 40

BUNTON

MISSILE

FUEL FILTER

An inline fuel filter is located in the fuel supply line. Inspect at every oil change to make sure it is clean and

unobstructed. Replace if dirty.

HYDRAULIC SYSTEM

Fluid level in the hydraulic system should be checked

after the first 5 hours of operation, and every 100

hours thereafter, or when a leak has occurred. If the

fluid is low, check all components for leaks.

To check, remove reservoir cap

. The fluid level

should be at the bottom of the filler tube. If low, top

up (do not overfill). Use one of the oils listed below:

– SAE 15W40 motor oil

– SAE 20W50 motor oil

– 15W50 synthetic motor oil

AFTER FIRST FIVE (5) HOURS

1. Remove plug

to drain hydraulic reservoir. Dis-

pose of used oil in accordance with local require-

ments.

2. Clean and replace the plug.

3. Change hydraulic oil filter

4. Fill the reservoir with fresh oil to the bottom of

the reservoir filler tube, using an oil from the list

above. Do not overfill.

PERIODIC OIL CHANGES

Change the hydraulic fluid and hydraulic filter

after each 500 hours of operation using the same

procedure given above.

NOTES:

View from right side

View from below machine

MAINTENANCE

Before servicing the hydraulic system, stop the engine, disconnect spark plug wires and disengage the PTO.
– After any hydraulic line is opened, plug or cap it promptly to reduce the risk of contamination.

– Do not use sealant tape on hydraulic pipe fittings. Use a liquid sealant that will dissolve into the system.

– Make sure all hydraulic connections are tight and hydraulic hoses and lines are in good condition before

applying pressure to system.

The machine's hydraulic system operates under high pressure. When checking for leaks, do not use your

hands to attempt to find a leak. Instead, use cardboard or paper. Escaping hydraulic fluid can be under suf

ficient pressure to penetrate skin and cause serious injury. If hydraulic fluid is injected into the skin, it must be

promptly removed by a doctor familiar with this form of injury or gangrene may result.

Содержание BUNTON 642246F









































Результаты поиска

Содержание BUNTON 642246F

Отзывы:

Похожие инструкции для BUNTON 642246F

Бренды по названию

Популярные бренды

Schiller Grounds Care BUNTON 642246F, Руководство оператора

Результаты поиска

Содержание BUNTON 642246F

Отзывы:

Похожие инструкции для BUNTON 642246F

Бренды по названию

Популярные бренды