manualshive.com logo in svg

Schier SI-75, Руководство по установке, Страница: 8 / 9

Поделиться
Скачать
Schier SI-75 Скачать руководство пользователя страница 8

5 

 Wet or Air Test Piping Per Local Code

Doing so may result in property damage, personal injury or death.

DO NOT AIR TEST UNIT OR RISER SYSTEM! 

Have a Leak?

Call customer 

care at 913-951-3300

Hours 8am-5pm CST, M-F 

Schier | SI-75 Installation Guide

page 8 of 9

6 

 Bring Covers Flush-to-Grade 

The SI-75 is ready for burial depth of 40" from finished grade to bottom of tank (or 13-1/2" to centerline of inlet). 
Deeper burials will require extending the cover adapters and possibly adding risers.

Measure dimension X to determine riser height needed. 

6a

See instructions included with FCR2. 

Riser Height  

Risers

Needed Required

0" - 4" 

None (use adapter)

>4" - 34" 

FCR2 (x1)

>34" - 64" 

FCR2 (x2)

>64" - 94" 

FCR2 (x3)

Loosen the cover adapter upper band 
clamp using 7/16" Nut Driver Bit. Adjust 
cover adapter heights as needed. 

Maintain a minimum 2-1/2" insertion 
depth. 

Tighten upper band clamp to 5 

-8 ft. lbs. of torque using 7/16" nut driver 
Bit. If required, cover adapters may now 
be tilted up to 10º in any direction using 
gasket flexibility.

6c

Make final cover adapter adjustments 

6b

Install risers if required

COVER ADAPTER ADJUSTMENT DETAIL

2-1

/

2" minimum

Cover

Safety Star 
access restrictor

Cover adapter

Gasket

Upper band clamp

Lower band clamp

Interceptor accessway 

Содержание SI-75










Отзывы:

Нет отзывов