14
ma chine is running; before performing tasks of any
kind release the main switch button located on the
handgrip, thus disconnecting the machine.
• Always keep hands away from the work area when the
machine is running; before performing tasks of any
kind release the main switch button located on the
handgrip, thus disconnecting the machine.
Fixing the Machine Fig.2.0
Note: we strongly recommend that you fix the mitre saw
safely on a workbench so that your machine is as stable
as possible.
1 Place the machine at the appropriate place and mark
the four bolt holes (15) on the workbench.
2 Drill the holes using a 10 mm drill.
3 Fix the saw on the workbench using bolts, washers
and nuts.
Mounting material is not included.
transporting the Machine Fig. 2.0-2.1
Slide the traction sled (1) until it stops and secure it with
the clamping screw (A).
Lower the cutting head downwards until it stops and push
down the lock lever (B).
Hold the mitre saw by the provided handle (19) for
transportation.
m
Assembly
WARNiNG! For your own safety, never connect the plug to
power source outlet until all assembly steps are completed
and you have read and understood the safety and operational
instructions.
Lift the saw from the packaging and place it on your
work bench.
installing the Dust Bag Fig. 2.2
Place the dust bag (18) on the outlet at the upper blade
guard.
Mounting the Clamping Jaw Fig. 2.3
Mount the clamping jaw (17) and secure it with the
clamping screw (C).
The clamping jaw has a quick adjustment, which is
triggered by pressing the button (D).
Attaching the side bars
The side support bars (10) help to support the material
when working with long work pieces. There are two
location holes (25) for a support bar on either side of
the table. Loosen the lock knobs on the back of the base
at the bottom. Ensure the side bars are fully inserted
before using them to support the work piece
The side support bar locking knobs (H) must be tightened
to secure the support bars in position.
Setting the tool
Note:
This tool is accurately adjusted before shipping from
the factory. Check the following accuracy and readjust if
necessary in order to obtain the best results in operation.
installation of the Angle Fence at 90°, Fig. 3
1 Loosen the angle clamping lever (1).
2 Lock the ratchet lever (2) towards the inside.
3 Move the cutting head to the right until it rests
against the fence.
4 Tighten the angle clamping lever (1).
5 Test the saw blade with a 90° angle to the saw table.
If an adjustment is necessary, loosen the lock nut (3) and
position the socket screw (4) in such a way that the saw
blade stands at 90° to the table. Re-tighten the lock nut.
6 Set the angle fence with the screw at 0.
installation of the Angle Fence at 45° Left. Fig.4
1 Loosen the angle clamping lever (1).
2 Move the cutting head to the left until it rests against
the fence.
3 Tighten the angle clamping lever (1).
4 Test the saw blade with a 45° angle to the saw table.
If an adjustment is necessary, loosen the lock nut (5) and
position the socket screw (6) in such a way that the saw
blade stands at 45° to the table. Re-tighten the lock nut.
installation of the Angle Fence at 45° Right. Fig. 4.1
1 Loosen the angle clamping lever (1).
2 Lock the ratchet lever (2) toward the outside.
3 Move the cutting head to the right until it rests
against the fence.
4 Tighten the angle clamping lever (1).
5 Test the saw blade with a 45° angle to the saw table.
If an adjustment is necessary, loosen the lock nut (5) and
position the socket screw (6) in such a way that the saw
blade stands at 45° to the table. Re-tighten the lock nut.
installation of the Contact Surface, Fig. 5
• Lower the cutting head and push in the lock pin. Make
sure the table is in 0 mitre position.
• Place a combination square against the fence and next
to the saw blade.
• Loosen the two screws (7) if the saw blade does not
touch the protractor.
• Adjust the fence so that the fence has full contact with
the square. Tighten the screws.
Adjusting the Laser Line Fig 5.1-5.2
1 To adjust the laser beam, take a board (approx. 200
mm x 300 mm) mark a line at the right angle and
place the board on the contact surface of the table.
2 Align the mark to the centre of the saw blade and
clamp it firmly with the clamping shoe.
3 Turn the laser on with the switch (23 Fig.1).
4 To adjust the laser line, pull the cover (A) and loosen
the slotted screw (B).
5 Now move the laser unit until the laser line fits in
with the marked line.
6 Fine adjustment can be done with the two slotted
