Scheppach HM80L Скачать руководство пользователя

Страница: 25 / 188



www.scheppach.com



[email protected]



+(49)-08223-4002-99



+(49)-08223-4002-58

Installation of the dust bag

• Squeeze together the metal ring on the dust bag

(12) and attach it to the outlet opening in the motor
area.

Emptying the dust bag

• By pressing the metal ring wings of the dust bag

(12) together the dust bag can be disengaged from
the outlet opening.

• Open the zipper of the dust bag and shake the

contents into a dustbin.

• Close the zipper and install the dust bag on the

machine again as described.

Assembling the work piece clamping device (fig.

1.1)

• Loosen the locking screw (17) and attach the work

piece clamping device (10) to the left or right of the

fixed saw bench.

• Afterwards, retighten the locking screws (17).

Assembling the work piece supports (fig. 1.1 –

1.2)

• Loosen the cross-head screw (14) and guide the

work piece support through the specified hole on
the side of the fixed saw bench.

• Make sure that the work piece support (15) is also

guided through the two plates (19) on the under

neath.

• Afterwards, retighten the cross-head screw (14).

• Repeat this process on the other side.

Assembling the support stand (fig. 1.1 – 1.2)

• Loosen the cross-head screws (18) on the under-

neath of the saw and guide the support stand (16)

through the specified holes on the back of the saw.

• Afterwards, retighten the cross-head screws (18).

Area of application

Intended application possibilities

The machine cuts:
• Wood and materials similar to wood
• Plastic

Unintended application possibilities

The machine is not suitable for:
• Ferritic materials, steel and cast iron, as well as

other material types which are not listed, particu

larly food.

• Mitre saw without guard.
•

Materials larger than the specified cutting data:

90°/90°

120 x 60 mm

90°/45°

80 x 60 mm

45°/90°

120 x 35 mm

45°/45°

80 x 35 mm

MOVING

Since the mitre saw is relatively small and light, its
location can be easily changed, even by a single per

son. After locking the locking knob (26 - Fig. 4) in the

bottom position, lift the mitre saw by the handle (34

- Fig. 4).

TRANSPORT

If the machine must be transported, carry it by the

handle (34 - Fig. 4) and place it in the original pack-

aging in which it was supplied. In the process, make
sure that it is correctly positioned in the package (see
arrows on the package).

If possible, the load should be fixed with ropes or

securing belts in order to prevent shifting during the
transport or parts of the load from falling down.

POSITIONING/WORK STATION

Position the machine on a work bench or on a flat

base so that the machine is supported as stably as
possible. Make sure that the machine is always se

cured to a workbench or table if possible. Secure the
machine through the holes on the base (7) of the ma

chine by using 4 screws on a workbench, an under

carriage o. eg..
When working with the machine, ergonomic factors
must be considered; the ideal height of the work ta

ble or the base is reached when the base surface
or the upper work surface is 90 to 95 cm above the
ground. The positioning of the machine must provide
for at least 80 cm of clearance in all directions and in
order to allow for cleaning and repair work as well as
necessary adjustments in observance of safety con

ditions and with sufficient room to manoeuvre.

CAUTION:

Position the machine in a zone which is

suitable in respect to the environmental conditions
and lighting. Never forget that the general environ

mental conditions play an extremely important role in
accident prevention.

CONNECTION TO THE POWER SUPPLY

Make sure that the socket is in a good condition. We
would like to remind you that the power supply must

be connected to a magnetic-thermal circuit breaker
which protects all lines from short-circuits and over-

Assembly

WARNING! For you own safety, only insert the

mains plug in an outlet when all assembly steps

have been completed and you have read and un-