Scheppach 5911249938, Перевод оригинального руководства пользователя

Страница: 34 / 68


www.scheppach.com /

service@scheppach.com /

+(49)-08223-4002-99 /

+(49)-08223-4002-58
34 | GB
clips into position on the frame (fig. 8).
10. Mowing with grass box:
Lift the discharge flap (15) with one hand and
hang the grass box (16) as shown in fig. 9.
11. Mulching:
If the grass box (16) is attached, remove it and
replace it with the mulch insert (19) as shown in
fig. 10-12.
Setting the cutting height
m
CAUTION!
Adjust the cutting height only when the engine is
switched off and the plug boot has been pulled.
• Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners are
damaged.
• To prevent any imbalance, replace blunt and/or
damaged blades as a set only (if applicable). To
carry out this check, first switch off the engine and
pull the spark plug boot.
• The cutting height is centrally adjusted with the cut-
ting height adjustor lever (fig. 13/ Item 14). 7 differ -
ent cutting heights can be selected.
• Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired po-
sition. (fig. 13)
Preparing the area to be mowed
Before mowing, carefully examine the area. Remove
stones, sticks, bones, wires, toys and other objects
that may be ejected.
9. Operation
m
ATTENTION!
Always make sure the device is fully assembled
before start-up!
Charge battery pack
Improper use of the battery and charger can result in
an electrical shock or fire.
When charging battery pack
• Charge battery pack only with original battery
charger.
• Do not use battery charger to charge any other
types of batteries.
• Keep battery charger dry. Avoid exposing battery
pack to rain or wet conditions.
• To reduce risk of damage to electric plug and cord,
pull by plug rather than cord when disconnecting
charger.
• An extension cord should not be used unless abso-
lutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock. If an
Include our item number, the device model and year
of manufacture in your order.
m
Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
8. Before first use
m
ATTENTION!
Always make sure the device is fully assembled
before start-up!
Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the instruc-
tions below.
Important! You will need the following additional tools
(not supplied) for assembly, and also for maintenance
work:
• A 1 litre measuring jug (oil/petrol resistant)
• A petrol can (5 litres is sufficient for approx. 6 op -
erating hours)
• A funnel (suitable for the tanks petrol filler neck)
• Household wipes (to wipe up oil/petrol residue; dis-
pose of these at a filling station)
• A petrol suction pump (plastic, available from DIY
stores)
• An oil can with hand pump (available from DIY
stores)
• 0,4 litre of engine oil (SAE 30)
Assembly
1. Take the mower and attachment parts out of the
packaging and check that all parts are present.
2. Attach the lower push bar (4a) to both sides of the
mower with one screw (a), 1 washer (c), 1 plastic
star grip nut (5) each. Make sure that the cables,
which will be attached later, are not in the way (fig.
2-3).
3. Attach the upper push bar (4) on the lower push
bar (4a) with one screw (a), one washer (b), one
plastic star grip nut (5) each on both sides (Fig.
4-5).
4. Guide the gas throttle through the electric starter
unit as shown in figure 5a.
5. Insert the throttle cable into the engine brake le-
ver (3) using a plier. (fig. 5b-5c)
6. Secure the electric starter unit (18) using the
screws (f) on the upper push bar (4). (fig. 5d)
7. Insert the pull start handle (17) in the designated
hook as shown in Fig. 6.
8. Fix the cables to the push bar with the cable clips
(18) provided (fig. 7).
9. Grass box (16) - open it up and click the plastic