Scheppach 5901502938, Оригинальное руководство пользователя

Страница: 28 / 52


www.scheppach.com /

service@scheppach.com /

+(49)-08223-4002-99 /

+(49)-08223-4002-58
28 | GB
cover lock (13) with the help of the 6 mm Allen key
(28) by turning this counter-clockwise. Then un-
lock the bottom cover lock (10) by unscrewing it
counter-clockwise.
• Slowly turn the saw band roller (2) clockwise. The
Bandsaw blade (22) should run centrally on the
saw band roller (2). If this is not the case, the angle
of the top saw band roller (2) must be corrected.
• If the Bandsaw blade (22) runs more towards the
rear edge of the saw band roller (2) then the set
screw (15) must be rotated anticlockwise.
• Open the locking screw for the top saw band roller
(14).
• Turn the bottom saw band roller (8) slowly by hand,
to check the position of the Bandsaw blade (22).
• If the Bandsaw blade (22) runs more towards the
front edge of the saw band roller (2) then the set
screw (15) must be rotated clockwise.
• After setting the top saw band roller (2), check the
position of the Bandsaw blade (22) on the bot-
tom saw band roller (8). The Bandsaw blade (22)
should also lie centrally on the saw band roller (8)
here. If this is not the case, the angle of the top
saw band roller (2) must be adjusted again.
• Turn the saw band roller a few times, until the ad-
justment of the top saw band roller (2) acts on the
saw band position on the bottom saw band roller
(8).
• Tighten the locking screw for the top saw band
roller (14).
• Once adjustment is complete, close the side cover
(11) again with the bottom (10) and top (13) cover
locks in reverse order.
9.6. Adjusting the saw band guide (Fig. 6-9)
Both the support bearing (36 + 42) and the guide
pins (37 + 46) must be readjusted after every saw
band change.
• Open the side covers (11) by undoing the cov-
er locking mechanisms (10) with the help of the
screwdriver (29).
9.6.1. Top support bearing (36) ( Fig. 6)
• Undo Allen screw for top support bearing (35).
• Move support bearing (36) sufficiently far that it
just no longer touches the Bandsaw blade (22)
(distance max. 0.5 mm).
• Retighten the Allen screw for the top support bear-
ing (35).
9.6.2. Adjusting the bottom support bearing
(42) (Fig. 8)
• Disassemble the saw table as per 9.1 in the op-
posite direction.
• Undo Allen screw for bottom support bearing (41).
• Move bottom support bearing (42) sufficiently far
that it just no longer touches the Bandsaw blade
(22) (distance max. 0.5 mm).
• Retighten Allen screw for bottom support bearing
(41).
9.6.3. Adjusting the top guide rollers (37)
(Fig. 6+7)
• Undo Allen screws for top retainer (40)
• Move top retainer (39), top guide rollers (37), until
the front edge of the guide rollers (37) is approx. 1
mm behind the tooth base of the saw band.
• Retighten Allen screws for top retainer (40).
• Slide the guide rollers (37) in the direction of the
saw band! Important note! The distance between
the guide rollers (37) and saw band (22) must not
exceed 0.5 mm. (Saw band must not jam)
• Retighten Allen screws (38).
• Turn the top saw band roller (2) a few times in a
clockwise direction.
• Check the setting of the top guide rollers (38) again
and adjust if necessary.
• If necessary, adjust the top support bearing (36)
(9.4.1).
9.6.4. Adjusting the bottom guide pins (46)
(Fig. 8+9)
• Disassemble saw table (7)
• Undo screw for bottom retainer (43) (Open-ended
spanner, size 10)
• Move bottom retainer (47), bottom guide rollers
(46), until the front edge of the bottom guide roll-
ers (46) is approx. 1 mm behind the tooth base of
the saw band.
• Retighten screw for bottom retainer (43).
• Undo Allen screws for bottom guide rollers (45).
• Slide the two bottom guide rollers (46) sufficiently
far in the direction of the saw band that the dis-
tance between the guide rollers (46) and saw band
(22) is max. 0.5 mm. (Saw band must not jam)
• Retighten Allen screws for bottom guide rollers (45).
• Turn the bottom saw band roller (8) a few times in
a clockwise direction.
• Check the setting of the bottom guide rollers (46)
again and adjust if necessary.
• If necessary, adjust the bottom support bearing
(42) (9.4.2).
9.7. Adjusting the top saw band guide (5) (Fig. 10)
• Undo locking handle for saw band guide (24).
• Turn the adjustment handle for the saw band guide
(23) to lower the saw band guide (5) as closely as
possible (distance approx. 2-3 mm) over the ma-
terial to be cut.
• Retighten locking handle (24).
• Check the setting before every cutting process and
adjust if necessary.
9.8. Adjusting the saw table (7) to 90° (Fig. 11+12)
• Set the top saw blade guide (5) fully upwards.
• Loosen the locking handle for the saw table (21)
by turning counter-clockwise.
• Place the angle bracket between the Bandsaw
blade (22) and saw table (7). Angle bracket not
included in the scope of supply.
• Tilt the saw table (7) by turning, until the angle to
the Bandsaw blade (22) is precisely 90°. If the saw
table is already on the screw (49) and a 90° angle
cannot be set, undo the nut (50) and shorten the