Scheppach 5901221904 Скачать руководство пользователя страница 27

Страница: 27 / 96

www.scheppach.com

GB | 27

j) Ensure the mitre saw is mounted or placed on

a level, firm work surface before use.

A level

and firm work surface reduces the risk of the mitre

saw becoming unstable.

k) Plan your work. Every time you change the

bevel or mitre angle setting, make sure the ad-

justable fence is set correctly to support the

workpiece and will not interfere with the blade

or the guarding system.

Without turning the tool

“ON” and with no workpiece on the table, move

the saw blade through a complete simulated cut

to assure there will be no interference or danger of

cutting the fence.

l) Provide adequate support such as table ex-

tensions, saw horses, etc. for a workpiece that

is wider or longer than the table top.

Workpiec-

es longer or wider than the mitre saw table can

tip if not securely supported. If the cut-off piece

or workpiece tips, it can lift the lower guard or be

thrown by the spinning blade.

m) Do not use another person as a substitute for

a table extension or as additional support.

Un-

stable support for the workpiece can cause the

blade to bind or the workpiece to shift during the

cutting operation pulling you and the helper into

the spinning blade.

The cut-off piece must not be jammed or

pressed by any means against the spinning

saw blade.

If confined, i.e. using length stops, the

cut-off piece could get wedged against the blade

and thrown violently.

Always use a clamp or a fixture designed to

properly support round material such as rods

or tubing.

Rods have a tendency to roll while be-

ing cut, causing the blade to “bite” and pull the

work with your hand into the blade.

p) Let the blade reach full speed before contact-

ing the workpiece.

This will reduce the risk of the

workpiece being thrown.

q) If the workpiece or blade becomes jammed,

turn the mitre saw off. Wait for all moving

parts to stop and disconnect the plug from the

power source and/or remove the battery pack.

Then work to free the jammed material.

Con-

tinued sawing with a jammed workpiece could

cause loss of control or damage to the mitre saw.

After finishing the cut, release the switch, hold

the saw head down and wait for the blade to

stop before removing the cut-off piece.

Reach-

ing with your hand near the coasting blade is dan-

gerous.

Hold the handle firmly when making an incom

plete cut or when releasing the switch before

the saw head is completely in the down posi-

tion.

The braking action of the saw may cause

the saw head to be suddenly pulled downward,

causing a risk of injury.

b) Use clamps to support the workpiece when-

ever possible. If supporting the workpiece

by hand, you must always keep your hand

at least 100 mm from either side of the saw

blade. Do not use this saw to cut pieces that

are too small to be securely clamped or held

by hand.

If your hand is placed too close to the

saw blade, there is an increased risk of injury from

blade contact.

c) The workpiece must be stationary and clamped

or held against both the fence and the table.

Do not feed the workpiece into the blade or cut

“freehand” in any way.

Unrestrained or moving

workpieces could be thrown at high speeds, caus-

ing injury.

d) Push the saw through the workpiece. Do not

pull the saw through the workpiece. To make

a cut, raise the saw head and pull it out over

the workpiece without cutting, start the motor,

press the saw head down and push the saw

through the workpiece.

Cutting on the pull stroke

is likely to cause the saw blade to climb on top of the

workpiece and violently throw the blade assembly

towards the operator.

e) Never cross your hand over the intended line

of cutting either in front or behind the saw

blade.

Supporting the workpiece “cross handed”

i.e. holding the workpiece to the right of the saw

blade with your left hand or vice versa is very dan-

gerous.

f) Do not reach behind the fence with either

hand closer than 100 mm from either side of

the saw blade, to remove wood scraps, or for

any other reason while the blade is spinning.

The proximity of the spinning saw blade to your

hand may not be obvious and you may be seri-

ously injured.

g) Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence. Al-

ways make certain that there is no gap be-

tween the workpiece, fence and table along

the line of the cut.

Bent or warped workpieces

can twist or shift and may cause binding on the

spinning saw blade while cutting. There should be

no nails or foreign objects in the workpiece.

h) Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the work-

piece.

Small debris or loose pieces of wood or

other objects that contact the revolving blade can

be thrown with high speed.

i) Cut only one workpiece at a time.

Stacked mul-

tiple workpieces cannot be adequately clamped

or braced and may bind on the blade or shift dur-

ing cutting.

Содержание 5901221904

































































































Результаты поиска

Содержание 5901221904

Отзывы:

Похожие инструкции для 5901221904

Бренды по названию

Популярные бренды

Scheppach 5901221904, Перевод оригинального руководства пользователя

Результаты поиска

Содержание 5901221904

Отзывы:

Похожие инструкции для 5901221904

Бренды по названию

Популярные бренды