www.scheppach.com
GB | 31
8.
Do not use saw blades made of high-speed alloy
steel (HSS steel).
9.
Only use saw blades for which the maximum per
-
missible speed is not lower than the maximum
spindle speed of the crosscut, drag and mitre saw
and which are suitable for the material to be cut.
10. Observe the saw blade direction of rotation.
11.
Only insertion the saw blade if you have mastered
their use.
12. Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
13.
Clean grease, oil and water off of the clamping
surfaces.
14.
Do not use any loose reducing rings or bushes for
the reducing of holes on saw blades.
15.
Make sure that fixed reducer rings for securing the
insertion tool have the same diameter and have at
least 1/3 of the cutting diameter.
16.
Make sure that fixed reducer rings are parallel to
each other.
17.
Handle insertion tool with caution. They are ideally
stored in the originally package or special contain
-
ers. Wear protective gloves in order to improve
grip and to further reduce the risk of injury.
18. Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
19. Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
20.
Only use the supplied saw blade for cutting wood,
never for the processing of metals.
21.
Only use saw blade diameters in accordance with
the markings on the saw.
22. Use additional workpiece supports, if required for
workpiece stability.
23.
Workpiece support extensions must always be se
-
cured and used during work.
24. Replace table inserts when worn!
25. Avoid overheating of the saw teeth.
26. When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose.
Replace damaged or worn saw blades immediate-
ly.
When the saw blade overheats, stop the machine.
Allow the saw blade to cool down before using the
machine again.
m)
Do not use another person as a substitute for
a table extension or as additional support.
Un-
stable support for the workpiece can cause the
blade to bind or the workpiece to shift during the
cutting operation pulling you and the helper into
the spinning blade.
n)
The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade.
If confined, i.e. using length stops, the
cut-off piece could get wedged against the blade
and thrown violently.
o)
Always use a clamp or a fixture designed to
properly support round material such as rods
or tubing.
Rods have a tendency to roll while be
-
ing cut, causing the blade to “bite” and pull the
work with your hand into the blade.
p)
Let the blade reach full speed before contact-
ing the workpiece.
This will reduce the risk of the
workpiece being thrown.
q)
If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from the
power source and/or remove the battery pack.
Then work to free the jammed material.
Contin-
ued sawing with a jammed workpiece could cause
loss of control or damage to the mitre saw.
r)
After finishing the cut, release the switch, hold
the saw head down and wait for the blade to stop
before removing the cut-off piece.
Reaching with
your hand near the coasting blade is dangerous.
s)
Hold the handle firmly when making an incom
-
plete cut or when releasing the switch before
the saw head is completely in the down posi-
tion.
The braking action of the saw may cause the
saw head to be suddenly pulled downward, caus
-
ing a risk of injury.
Safety Instructions for the handling of saw blades
1. Do not use damaged or deformed saw blades.
2.
Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
3. Do not use saw blades made of high speed steel.
4. Check the condition of the saw blades before us-
ing the crosscut, drag and mitre saw.
5. Make sure that a suitable saw blade for the materi-
al to be cut is selected.
6.
Only use saw blades recommended by the man
-
ufacturer.
7. Saw blades designed to cut wood and similar ma-
terials must comply with EN 847-1.
