Scheppach 5801801985, Оригинальное руководство пользователя

Страница: 11 / 20

11 GB
4 Remove the outer flange (16) and the saw blade (10).
(Caution: risk of injuries, wear protective gloves)
5
Insert the new blade and flange.
6 Screw in and tighten the saw blade locking screw
while keeping the shaft locking mechanism pressed
again.
7 Set the plunge saw to its original position.
Adjusting the splitting wedge, Fig. 7
Adjust the distance between saw blade and splitting
wedge after a saw blade replacement, or whenever nec-
essary.
Put the saw in the same position as you do when replac-
ing a saw blade.
Unfasten the adjustment screw (18) using an Allen key
and set the splitting wedge 2-3 mm higher than the saw
blade, then retighten the adjustment screw.
Operations
After having performed all the above procedures and
opera tions, you may begin cutting.
ATTENTION: Always keep hands away from the cutting
area and do not try to approach it when the machine is
running.
Switching the product on/off, Fig. 1
To switch the plunge-cut saw on, press the on/off switch
(4). To switch off, release the on/off switch (4).
Operating and holding the plunge-cut saw, Fig. 8
1
Secure the work piece so that it cannot get displaced
or moved while sawing.
2 Only move the saw forwards.
3 Grip the saw tightly with both hands ensuring that one
hand is placed on the main handle and the other on
the front handle.
4 When using a guide rail, it must be fastened with
screw clamps.
5 Make sure the power cable is not placed in the saw-
ing direction.
Sawing
1
Place the front part of the machine onto the work
piece.
2 Switch the machine on using the on/off switch (4).
3 Press the plunge-cut trigger (3).
4 Push the saw downwards to reach the sawing depth.
5 Push the saw forward evenly.
6 After finishing the sawing cut, switch the machine off
and move the saw blade upwards.
Plunge-cuts, Fig. 9
1
Place the saw onto the work piece.
2 Place the cutting indicator with the rear arrow (A) on
the marked plunge-cut position.
3 Switch the machine on and push the saw downwards
until you reach the set cutting depth.
4 Move the saw forwards until the cutting indication (C)
has reached the marked point.
5 After completion of the plunge-cut, move the saw
blade upwards and switch the saw off.
Cutting with rails (otional)
1
Place the machine in the guide rails. can be read-
justed using the hex driver included in the delivery,
when there is the risk of the adjusting screws releas-
ing by themselves.
2 Turn on the machine by pressing the on/off switch (4).
3 Press the dip trigger (3).
4 Press the saw downwards to reach the sawing depth.
During first use the rubber lip is sawn off and thus
splitter protection is guaranteed up to the saw blade.
5 Push the saw uniformly forwards.
6 Turn off the machine and tilt the saw blade to the top
when the saw cutting is complete.
Sawing with dust suction
Connect the suction hose to the exhaust nozzle - Ø 38
mm (12).
Maintenance
m
Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time
using a cloth. In order to extend the service life of the
tool, oil the rotary parts once monthly. Do not oil the
motor.
When cleaning the plastic do not use corrosive prod-
ucts.
Brush inspection
Check the 2 carbon brushes after the first 50 operating
hours with a new machine, or when new brushes have
been fitted. After carrying out the first check, repeat the
check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the spring
or contact wire are burned or damaged, it is necessary
to replace both brushes. If the brushes are found to be
usable following removal, it is possible to reinstall them.
If specialist personnel must be brought in for ex-
traordinary ser vice or repairs during the warranty
period and thereafter, please contact a service pro-
vider recommended by us or con tact the manufac-
turer directly.
• Overhauls, maintenance work, cleaning, as well as
the eli mi nation of any malfunctions must only be un-
dertaken af ter turning off the motor.
• All protective and safety equipment must be rein-
stalled immediately upon completion of any repair or
maintenance work.