Scheppach 5801801985, Оригинальное руководство пользователя

Страница: 6 / 20

6 GB
Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
m
Important!
When using electric tools safety precautions should
always be followed to reduce the risk of fire, electric
shock and personal injury including the following. Read
all these instructions before attempting to operate this
product and save these instructions. Keep this manual
in a safe place, so that the information is available at
all times. If you give the equipment to any other person,
hand over these operating instructions and safety regu-
lations as well. We cannot accept any liability for dam-
age or accidents which arise due to a failure
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only
be operated by persons who were instructed concern-
ing the operation of the machine and who are informed
about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety notes contained in the present
operating instructions and the special regulations of
your country, the generally recognized technical rules
for the operation of wood working machines must be
observed.
Device description (Fig. 1-19)
1. Handle/hand grip
2. Front handle
3. Plunge-cut trigger
4. On/off switch
5. Base plate
6. Adjustment screw for depth of cut
7. Scale for depth of cut
8. Mitre adjustment screw
9. Mitre square
10. 90-degree adjustment screw
11. Saw blade
12. Suction nozzle
13. Motor
14. Shaft locking mechanism
15. Adjustment screw for guide rail
Unpacking
•
Open the packaging and remove the device carefully.
•
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
•
Check that the delivery is complete.
•
Check the device and accessory parts for transport
damage.
•
If possible, store the packaging until the warranty pe-
riod has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal -
lowing and suffocation!
Intended use
Plunge cut saws are intended to be used for sawing
wood, materials similar to wood, plaster and cement
bonded fibre materials and plastics.
The equipment is to be used only for its prescribed pur-
pose. Any other use is deemed to be a case of misuse.
The user / operator and not the manufacturer will be li-
able for any damage or injuries of any kind caused as
a result of this.
The equipment is to be operated only with suitable saw
blades. To use the equipment properly you must also
observe the safety information, the assembly instruc-
tions and the operating instructions to be found in this
manual.
All persons who use and service the equipment have to
be acquainted with this manual and must be informed
about the equipment’s potential hazards. It is also im-
perative to observe the accident prevention regulations
in force in your area. The same applies for the general
rules of health and safety at work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes. Even when the equipment is used
as prescribed it is still impossible to eliminate certain
residual risk factors. The following hazards may arise in
connection with the machine’s construction and
design:
•
Contact with the saw blade in the uncovered saw
zone.