background image

 

12 

3. Operation 

 
 
 
 

 

 

selection 
switches 
 
 
 
illuminated 

 

control 
push-buttons   

 

 

 

 

 

 

              

                                                       

 
 
 
 

 
3.1 By-pass activation 

 

The by-pass is activated by turning the switch located on the computer box clockwise. When the 
by-pass  is  activated,  all  the  electronic  functions  (diagnostic,  automatic  washing,  etc.)  are 
disabled, and the unit works in manual mode (the pumps 1 and 2 are activated acting directly on 
the  PUMP1  and  PUMP2  selectors).  It  is  not  possible  to  perform  fresh  water  washing  with  by-
pass  activated.    By-pass  activation  is  signaled  by  the  continuous    green  light  of  the  start  push-
button.  
 
The operation with the by-pass is necessary only in the following two circumstances: 
 

 

Plant  first  start-up  or  plant  restart  after  maintenance  operations.  The  use  of  the  bypass  is 
required at start up when purging air from the system. Without this in operation the computer 
would sense that there was deviation from normal operation tolerances and would continually 
shut the unit down.  

 

 

Electronic failure 

In the case of electronic control system failure, the by-pass allows use of the plant manually by 
selecting pump 1 and pump 2 switches manually. It will however not allow fresh water flushing 
of the unit as the Electro valve is controlled by the computer. 
IMPORTANT 
Do not engage the by-pass without good reason
, as all diagnostic and automatic functions are 
disabled when the by-pass is activated. 

PUMP 1  

 PUMP 2 

        AUT. WASHING  

 

 

 
 
 

 

 

 

 

 

 

START                   STOP 

     MAN. WASHING 

  

     

          

 

 

 

      ALLA 

 

 

 

 

 

 

 

 

 

 
 

 

 

 

 

              

Содержание READY Electron 60
























Отзывы: