background image

 

15 

 

Fresh water production with automatic washing 

     (

For  use  when  the  watermaker  is  not  used  on  a  daily  basis  or  when  automatic  washing  is               

required after every water making session.)   
 
1.

 

Preset the pumps by turning the PUMP1 and PUMP2 switches clockwise.  

 
2.

 

Preset the automatic washing by turning the AUT. WASHING switch clockwise. 

 
3.

 

Push  the  START  button  to  start  the  plant  (the  START  push-button pilot light come on and 
the production will begin). 

 
4.

 

Push  the  STOP  button  at  the  end  of  the  production  cycle.  The  plant  will  not  turn  off 
immediately,  but  a  washing  cycle  will  be  automatically  activated  lasting  approx  50sec. 
During the cycle the MAN WASHING push-button pilot yellow light will also light up. The 
watermaker will automatically shutdown after the washing cycle has finished. 

 
The fresh water consumption during an automatic washing operation is approx. 7 to 8 litres 
 
  

 

Manual washing cycle 

(If the unit is to be left unused for 2-3 months) 
 
This operation is not intended for  fresh water production, but  serves to perform a deeper rinsing 
of the watermaker, prior to long periods of inactivity. 
Before starting the manual washing, ensure that there is a sufficient quantity of fresh water inside 
the  vessel's  water  tank.    Fresh  water  consumption  during  this  washing    cycle  is  approx.  10 
litre/min. 
 
1.

 

Turn on the pressure water system. 

 
2.

 

Preset the pumps by turning the PUMP1 and PUMP2 switches clockwise.  

 
3.

 

Do  not  preset  the  automatic  washing.  Check  that  the  AUT.  WASHING  switch  is  in  the 
vertical position. 

 
4.

 

Push  the  MAN  WASHING  button  to  start  the  washing  cycle  (the  START  and  MAN 
WASHING button pilot lights will turn on). 

 
5.

 

Push the STOP button to stop the washing cycle. 

 

Do  not  let  this  procedure  continue  for  more  than  10  minutes  as  this  is  more  than  sufficient  to 
remove any build up of salt in the watermaker, It will also very quickly empty your water tank. 
  
 
 
 
 
 
 
 
 
 

 
 

Содержание READY Electron 60
























Отзывы: