background image

 

 

 

2 - GENERAL WARNINGS & INFO TO THE RECIPIENT                  

COD: 100M12/24.B.2021

 

EN 

 

THE PRESENT MANUAL BELONGS TO - 

Schenker Italia 

-  ALL RIGHTS RESERVED 

  ATTENTION 

 

Any technical changes or operating conditions indicated that affect the correct operation or 
safety  of  the  machine  must  only  be  carried  out  by  the  manufacturer's  technical  staff  or  by 
technicians formally authorized by the manufacturer. Otherwise, SCHENKER ITALIA declines 
any responsibility for changes or damages that may result from it. 

 

2.3  Warranty 

The equipment and the relevant accessories are guaranteed 12 months from delivery. The guarantee does 
not  include 

consumable  items  (filters,  carbon  filters,  membranes,  etc.).  The  “ERS”  pressure  amplification 

device is guaranteed 36 months, provided that the annual maintenance is per-formed at a Schenker service 
point. 
The guarantee covers faults, defect of materials and parts. It is limited to the replacement or re-pair of faulty 
parts. The expense for the disconnecting and reinstalling on the vessel and transport of the equipment from or 
to our Service Point, or our factory will be at the customers own expense. 
The un

der guarantee delivered parts transport, will be at customer’s own risk. 

In  case  of  repairs  under  guarantee  performed  by  our  technicians  on  the  customer  vessel,  the  faulty  parts 
replacement cost will be at Schenker's expense, while manpower and travel expenses will be charged to the 
customer.  The  guarantee  does  not  include  faults  caused  by  negligence  in  operating,  maintenance  and 
installation of the device (if not carried out by an authorised Schenker Service point). 
Dismantling by non-authorized personnel will render void all guarantees. Schenker Italia cannot be held liable 
for any direct or indirect damage caused by the malfunctioning equipment, limiting its responsibility to the repair 
and replacement of faulty parts. 

 
 

  ATTENTION 

 

SCHENKER ITALIA declines any responsibility for improper use of the machine, for damages 
caused as a result of operations not covered by this manual or unreasonable use. 

Содержание MODULAR 100













































Отзывы: