background image

MP-000022 - A 

 
 
 
 

INSTALLATION 

 

•  This  installation  must  conform  according  local  codes  (AS/NZS  5601).  In  the  absence  of 

local  codes,  the  installation  must  conform  to  the  National  Fuel  Gas  Code,  ANSI  Z223.1, 

Natural  Gas  Installation  Code,  CAN/CGA-B149.2,  or  the  Propane  Installation  Code, 

CAN/CGA-149.2.  For  installation  under  ventilation  hood  only.  The  manufacturer  is  not 

responsible  for  installation.  After  all  connections  and  installation  is  in  conformity  with  this 

manual, starting pilot/burners lighting procedure. 

• Remove the Gas Barbecue from the packaging; 

• The Gas Barbecue should be installed where there is air circulation; 

• Make sure the Gas Grill is levelled; 

• The rotating system requires 240 volt power. (Check that the voltage is correct); 

• Make sure all removable components are properly secured: burners, pilot, protective cover, 

bars, stones, manifold. Pressure in 0.8kpa Natural Gas or 2.6kPa for LPG measured at the 

manifold test point (see location of this test point on page14 detail D). 

• Installer can use suitable 3/4" gas hoses that complies with standard AS/NZS1869 Class B 

or D.  If a gas hose is used for connection, a suitable safety chain is to be installed that does 

not exceed 80% of the length of gas hose, this chain is to be fixed securely to the appliance 

& the rear wall. 

•  Gas  installation  should  be  done  taking  into  account  the  number  of  burners  in  the  Gas 

Barbecue.  Each  burner  consumes  0.3125  (m³/h)  of  natural  gas.  Therefore,  the  gas  battery 

must be made according to the flow capacity required by the burners (0.3125 m³ / h); 

• Each burner corresponds to: 16.880 MJ/h. 

• For installation a gas regulator gas valves must  be used; for  units with 1 meters there is 

one gas inlet so just one valves will be used and for larger than 1 m units two gas inlets will 

have in your unit so it is necessary two gas pressure regulator valves.   

 

Notes: 

 

•  Consult  the  technical  specifications  of  the  barbecue  and  call  a  technician  specialized  in 

gas; (Preferably the same as the contracted gas company); 

Содержание LVR 350A




























Отзывы: