Scarab Vampire Скачать руководство пользователя страница 5

Страница: 5 / 23

Page 5

version 1.0.1 SCARAB™ Vampire Airframe guide

Preparing the Scarab™ Airframe plates

Base Plate

1. Sand rough edges with curved diamond file

Use diamond file to smooth curved edges of the frame, including

the beetle wings to prevent wires being cut by sharp edges.

Only light scraping is required. Do both sides and outside edges

Take care not to slip and scratch the plates.

carbon conducts electricty

Attaching Delrin

Boomholders

Insert M2*8 boomholder bolts into the Scarab

™

Airframe plate

from the bottom.

Place a small amount of loctite® onto bolt then screw on the

21mm Stainless Steel Shaft.

There are 6 booms on a Scarab

™

Vampire plus an additional

empty boom holder at the rear for tail attachment stability.

Ensure no loctite® is on the outside of the shaft as it
will lock boomholders. Wipe clean.

Repeat until all shafts are done on base.

NB:

removing all sharp edges

sharp edges can cut high current wires and

cause fires

first push

then turn

Push Delrin® boomholder bases onto shafts.

Tighten the M2*8 boomholder bolts in base of Scarab

™

frame

now using 1/16th Pro Tool (hex key can alternatively be used).

Push Pro Tool in straight, otherwise bolt with strip.

Screw heads are stainless steel which is soft,

Pro Tool is hardened steel which is very hard.

If M2 heads are stripping out, this is a

technique fault. You are not pushing

the Pro Tool firmly in the first instance.

A bolt with correct alignment require almost

zero force to turn - a cross-thread bolt will

be very stiff after one or two turns - STOP

Place boomholder tops on.

Screw M2*8 bolts into top of shafts finger tight to test / check
tolerances on all shafts and the threads on the M2 bolts

DO NOT SKIP THIS STEP,

or you will regret it later when you

are pulling your whole frame apart to replace once shaft.

NB:

Содержание Vampire
























Результаты поиска

Содержание Vampire

Отзывы:

Бренды по названию

Популярные бренды

Scarab Vampire, Руководство по сборке

Результаты поиска

Содержание Vampire

Отзывы:

Бренды по названию

Популярные бренды