Scarab Vampire Скачать руководство пользователя страница 19

Страница: 19 / 23

Page 19

version 1.0.1 SCARAB™ Vampire Airframe guide

Battery

Attach female velcro to battery.

Attach Lipo to base plate of Scarab

™

Airframe with velcro.

Battery should be oriented toward the back of the copter.

The battery is moved to set the balance point.

Adhesive v

elcro stops Lipo from slipping

Velcro

strap

, holds Lipo in place.

There are 3 possible positions for the battery:

1. for carrying a go pro

2. for carrying a heavy APSC camera

3. for no camera

ensure to position your battery accordingly.

Check Scarab

™

Copter is correctly weighted with Lipo

on board by balancing on index fingers. Copter should tilt

slightly toward the front. ALWAYS check CofG

Pre-flight inspection

Below - get used to to doing a full pre-flight inspection

everytime.

Its a full aircraft and requires methodical checkng. A

combination of eyeball - visual inspection and manual

checking - physical tightness checks - your quad does

not glide - if something goes wrong it will exit the flight

envelope.

Always do a Pre-flight and Post flight

check - dont become complacent.

be systematic and ALWAYS check

prop attachment - wiring and Temps.

Use cell-by-cell monitoring of LiPo

C of G test

set 10mm forward

of centre point

Содержание Vampire
























Результаты поиска

Содержание Vampire

Отзывы:

Бренды по названию

Популярные бренды

Scarab Vampire, Руководство по сборке

Результаты поиска

Содержание Vampire

Отзывы:

Бренды по названию

Популярные бренды