Scarab Vampire Скачать руководство пользователя страница 21

Страница: 21 / 23

Page 21

version 1.0.1 SCARAB™ Vampire Airframe guide

Scarab™ Hand Maiden - hand held test

First test PROPS OFF - then if safe add props for Hand Maiden

1. Always turn the Tx on first - then turn it off last - reason

is Failsafe - make sure you understand failsafe and have

programmed the failsafe condition!

2. Hold the craft securely by the core body - either above your

head - or away at arms length - secure all loose wires - no

loose clothing!

Use proper Eye protection - set ACRO mode only.

DANGER - props can cut ! Use common sense and take

safety precautions to suit your experience

3. Wear eye protection ! - do a test run to check the PARIS

™

Carbonbird

™

ESC / Carbonbird

™

Engines - if an engine

stutters or hesitates - cut power - STOP - re-check all

wiring - or you will smoke your ESCs and the engines if you

continue - so STOP - investigate the wiring!

At 1/3 throttle all Gyro responses are normal - resists tipping

in all directions - stick orientation is correct - yaw stick input

is correct - low power systems response check.

4. Learn the switch position for Auto LEVEL - ON/OFF .

MAG on/off and BARO on/off

5. All engines MUST start together to show all ESCs are

programmed with THROTTLE LEARNING - see wiki - see

Carbonbird

™

Engines page on MultiWiiCopter.com website

6. All run smoothly up to full power - Same programming -

timing setting - this is the time to check all motors and power

systems are good. Should feel balanced. Make sure all modes

are OFF - ACRO mode only.

7. ZERO vibration in the frame and props

8. Does not want to rotate - yaw - feels balanced in your hand

- smooth

If anything seems wrong, - then DON’T FLY. Aviation works
on 100% perfect - not 98%

If you never tried RC before, use a Flight simulator first -

AEROSIM RC - with Scarab™ Copters.

NB:

Содержание Vampire
























Результаты поиска

Содержание Vampire

Отзывы:

Бренды по названию

Популярные бренды

Scarab Vampire, Руководство по сборке

Результаты поиска

Содержание Vampire

Отзывы:

Бренды по названию

Популярные бренды