Note:
must be set to
Normal
for this setting to apply.
You can also toggle this setting by pressing
ATT
when the object is in the display in Scan mode.
Delay:
When set to '
On
', a delay is used to wait for reply traffic after a transmission according to the
Delay Time
setting for the object. Default is
On
.
Press
◄
or
►
to select
On
or
Off
.
Note:
You can also do this by pressing
FUNC
then
.(DELAY)
when the object is in the display in manual, program, or scan modes.
Delay Time:
is set to
On
.
Enter the amount of time,
1-250
(
.
1 - 25 seconds), to set the delay. Default is
20
(2 secs).
Digital AGC:
When set to '
On
', instantly compensates for low user audio levels that are common on digital systems. '
G
' (
On
) or '
g
' (
Off
) will appear in the
right
of the display when a channel is active to indicate AGC status. Default is
On
.
Press
◄
or
►
to select
On
or
Off
.
SuperTrack:
decoding algorithm. When set to '
On
', may help reception on some systems. Default is
On
.
Press
◄
or
►
to select
On
or
Off
.
AudioBoost:
When set to '
On
', sets a 6 dB boost to audio levels when the object is active. Default is
Off
.
Press
◄
or
►
to select
On
or
Off
.
Hit Count:
When
Hit Counts
(in the
GLOB
menu) is set to '
On
', will increment each time a transmission is received on the object.
Enter a number (
0-9999
) to change the count if you wish or press
F3
(
Dflt
) to reset to
0
.
TSYS (Trunked System) Menu
The Trunked System menu is used when
editing
trunking system objects. To
create
a Trunked System object see
Creating Objects
. Trunked system
objects are assigned object numbers automatically but are not assigned to scan lists; just the talkgroups associated with the system are assigned to the
scan lists. There is a 32 control channel limit for a trunking system. Large Multi-site systems with more than 32 control channels will have to broken up into
smaller systems. '
Duplication
' will copy a system but each ID can only be associated with one system. You will have to have to re-enter (or duplicate) all
the IDs for the new system. That's when the software comes in handy.
To
Edit
an existing Trunked System object
press
PGM
then
F2
(
EDIT
)
.
Press
►
until
TSYS
is over
F3
then press
F3
.
Press
▼
or
▲
to scroll to the trunked system and press
F2
(
EDIT
). See also
Finding Objects
.
Use
▼
or
▲
to select each option
.
Menu changes do not take effect until the menu is saved-F1
(
Save
).
If you forget to save any changes, you will see '
Unsaved Changes! Go Back?
'.
Press
F1
(
Yes
) to go back or
F3
(
No
) to exit without saving.
If you are
creating a new trunked system
, you will be returned to the Talkgroup Menu when you save the Trunking System Menu
.
Then go to the
Talkgroup Menu
to finish editing the Group Wildcard ID that was automatically created.
Narrow FM
Threshold Hi
(Motorola/P25 only)
AutoMove HRs
(LTR only)
Threshold Lo
(Motorola/P25 only)
Invert Data
(EDACS Narrow only)
T Tables
(Motorola/P25 only)
DIG AGC
Multi-Site
(Motorola/P25 only)
Fleet Map
(Motorola Type I/IIi only)
Check All CC
(Motorola/P25 only)
Type:
Selects the type of trunking system.
Note for Motorola/P25 systems
: If you are not sure if the system is Motorola or P25, look at the
system voice
for your system. Those entries that say
System Voice: Analog and APCO-25 Common Air Interface
are not true Project 25 systems as
they have one or more analog talkgroups. Program these systems as a
MOT
system and let the scanner detect the digital. If the System Voice says
System Voice: APCO-25 Common Air Interface Exclusive
then the system is a true Project 25 system and program it as a
P25
system.
Press
◄
or
►
to select:
MOT 800/900
- for Motorola 700/800/900 MHz
analog
or
mixed
(analog and digital) trunked radio systems that use the 3600 baud control channel.
MOT VHF/UHF
- for Motorola VHF/UHF
analog
or
mixed
(analog and digital) trunked radio systems.
P25 MANUAL
- for Motorola 700/800/900/VHF/UHF Project 25 systems where it is necessary to manually set the channel table information or if you
wish to use the default table data (for 700/800/900 MHz systems).
P25 AUTO
- for most Motorola 700/800/900/VHF/UHF Project 25 systems that send channel table information over the system control channel.
EDACS STD
- for most 800 MHz EDACS systems using a 9600 BPS control channel.
EDACS NARROW
- for most 900 MHz and some VHF/UHF EDACS systems using a 4800 BPS control channel.
LTR
- for Logic Trunked Radio (LTR) systems.
Tag:
Press
SEL
/
ENT
to change the default object name-'
System
' to something different.
See
Enter text
or
Enter Qtext
.
Frequencies:
Press
SEL
/
ENT
to enter the frequencies for the trunking system. For Motorola systems you only need to enter the control channel
frequencies.
Note:
EDACSs frequencies also have to be entered in LCN order. See
.
See also
BandPlan
Expert Settings
' menu) for step size defaults.
Enter the
frequency
and press
SEL
/
ENT
.
Press
▼
to move to the next channel number and repeat for all the frequencies.
Press
F1
(
Save
) to exit.
L/Out:
Sets the lockout status of the system. Default is
Off
.
Press
◄
or
►
to select
On
or
Off
.
Atten:
When set to '
On
', applies 20 dB of attenuation to all transmissions in the system. Useful in areas where interference from nearby strong signals is
