Warning: The scanner will charge continuously with the scanner turned off and plugged into external power
. (External smart charger is
strongly
recommended).
Enter the number of hours,
0 - 16
the charger will charge.
AttenMode
Sets the global attenuator
mode
.
Global
applies attenuation (on or off) to all objects.
Normal
uses object attenuation settings. '
G
' will appear
in the
middle
of the display when set to
Global
. See chart below. Default is
Global
. See also
Press
◄
or
►
to select
Normal
or
Global
.
Normal
- the attenuator follows the individual object attenuator setting.
Global
- applies attenuation radio-wide regardless of object settings
only
when
Global Atten
is set to
On
. '
G
' will appear in the display when scanning
or searching.
Note:
You can also toggle this setting by pressing
FUNC
then
ATT
in Scan or Search mode.
Global Atten
Sets global attenuation (on or off) to every object regardless of the object attenuation setting. Indicators will appear in the
middle
of the
display to indicate attenuation status. Default is
Off
. See chart below.
Press
◄
or
►
to select
On
or
Off
.
Note:
You can also toggle this setting by pressing
ATT
in Scan or Search mode.
Attenuation Settings
Object Attenuation
AttenMode
Global Atten
Display
Results
Off
Normal
Off
No
G
or
A
Object/system/search attenuation
Off
On
Normal
Off
A
Object/system/search attenuation
On
On
or
Off
Global
Off
G
Attenuation
Off- all objects/systems/searches
On
or
Off
Global
On
GA
Attenuation
On- all objects/systems/searches
Clear Hits
Clears
all
the hit counters for
all
objects if
Hit Counts
(see next entry) has previously been set to
On
. You can clear
each
object's hit count by
going to each object's menu.
Press
SEL
/
ENT
. '
Really clear all object hit count data?
' will appear. Press
F1
(
Yes
) to clear or
F3
(
No
) to exit.
Hit Counts
When set to '
On
', keeps track of how many transmissions are received (or not received) for each object. Default is
No
.
Press
◄
or
►
to select
Yes
or
No
.
Dflt ScanList
Sets the default Scan List destination for programming new objects and the
Stor
(
F3
) location for conventional objects found with
Stalker/Sweeper, Limit, Service, and Tune searches. Use
1-20
for the normal Scan Lists. Use
21
for the Favorite List. Use
22
for the Skywarn List. Use
0
(no scan list) if you want to (will have to) select a different Scan List each time. Default is Scan List
1
.
Enter
0 - 22
and press
ENT
.
Note:
Any object assigned to
0
(no scan list) will not be scanned. You can't select this list to scan.
Priority
Turns priority scan on or off. The display will show '
PRI
' (uppercase) when priority is on and '
pri
' (lowercase) when priority is off. Default is
Off
.
Press
◄
or
►
to select
On
or
Off
. See also
Notes:
You can also do this by pressing
FUNC
then
PRI
in scan mode. You can enabled priority scan even with no objects set for priority.(?)
WxPriority
Allows you to check the specified weather frequency periodically while scanning to see if the All Hazards 1050 Hz Warning Alert Tone (WAT) is
present. If the WAT is present, the scanner will sound an alarm and tune to the programmed weather frequency to monitor the nature of the alert.
WX PRI
Check
appears briefly on the bottom line of the display in scan mode. Default is
Off
.
See also
Weather Settings
(in the '
Expert Settings
' menu).
Press
◄
or
►
to select
Off
or one of the
preprogrammed weather channels
.
Notes:
You can also do this by pressing
WX
then
PRI
in Scan mode. Does not work in Search or Stalker/Sweeper Modes.
Scan Lists
Allows you to enable (turn on) and disable (turn off) the (normal;
1-20
) Scan Lists to scan.
Press
SEL
/
ENT
to edit.
Press
▼
or
▲
to select the Scan List and press
SEL
/
ENT
to enable or disable the list. An asterisk (
*
) appears next to all enabled scan lists.
Note:
You can also do this by pressing the
number keys
on the keypad for single digit scan lists or
FUNC
then the
number keys
for double-digit
scan lists (
FUNC
then
1
for 11) in Scan mode.
SRCH L/Outs
Allows you to enter a sub menu for reviewing, editing or deleting
search
lockout frequencies.
Press
SEL
/
ENT
to edit. Press
▼
or
▲
to select the locked out frequency.
To unlock the frequency press
F3
(
Del
).
To add a frequency press
▼
or
▲
to select an empty slot and enter the frequency.
Press
F1
(
Save
) to save and exit.
Clear FAV
Clears the 'Favorites' Scan List.
Press
SEL
/
ENT
. '
Really remove all objects from FAV scan list?
' will appear. Press
F1
(
Yes
) to clear or
F3
(
No
) to exit.
Memory Info
This will show you total number of objects, free space percentage, number of conventional channels, talkgroups, trunked systems, and
search objects.
Press
SEL
/
ENT
. Press
F1
(
Done
) to exit.
Tune LED
When set to '
On
', activates the signal strength driven LED when in 'Tune' mode. The color of the LED will change as the signal increases (from
'color 0' to 'color 7' ?). Default is
Off
.
Press
◄
or
►
to select
On
or
Off
.
Color 0-7
Here is where you customize the colors used to illuminate or flash the LED when certain objects are active. They set the intensity of red, green,
and blue for each of the 8 selectable colors. By default,
Color 0=Off
,
Color 1=Red
,
Color 2=Yellow
,
Color 3=Green
,
Color 4=Cyan
,
Color 5=Blue
,
Color 6=Magenta
, and
Color 7=White
.
For each color, (
0-7
), press
SEL
/
ENT
to edit.
Press
◄
or
►
to select
R
(red),
G
(green), or
B
(blue).
Use the number keys (
0-9
) to set preset intensities or press
▼
or
▲
to select your own custom intensity.
Press
◄
or
►
to select the next color and repeat.
Press
F1
(
Done
) to save and exit.
Qtxt 0-9
See
Customizing Qtext
.
