Scania OC16 Скачать руководство пользователя страница 58

Страница: 58 / 73

Electrical system

OPM 320 en-GB

Scania CV AB 2019, Sweden

Remove the spark plug connector by pulling

it straight upwards.

IMPORTANT!

Do not pull on the arm as this could damage the

spark plug connector.

Check that the spark plug connector does not

have any visible damage.

Unscrew the spark plug using the spark plug

socket.

IMPORTANT!

Do not touch the spark plug insulator with your

fingers. If this occurs, clean the insulator with al-

cohol.

Place the new spark plug in the spark plug

socket and tighten the spark plug. Tightening

torque 30 Nm (22 lb-ft).

IMPORTANT!

Do not lower the spark plug through the rocker

cover since this could cause the gap between the

spark plug electrodes to be incorrect. Always

place the spark plug in the spark plug socket be-

fore fitting. The correct gap between the spark

plug electrodes is 0.25 mm.

Fit the spark plug connector.

Содержание OC16










































































Результаты поиска

Содержание OC16

Отзывы:

Похожие инструкции для OC16

Бренды по названию

Популярные бренды

Scania OC16, Руководство оператора

Результаты поиска

Содержание OC16

Отзывы:

Похожие инструкции для OC16

Бренды по названию

Популярные бренды