•
Connection the power to check the showcase before using
,
the showcase can
be used until the temperature decreases obviously after 30 minutes.
•
You should adjust the temperature control according to the requested
temperature and quantity of the stored food and the environmental
temperature
.
•
Before putting the stuff into the showcase please adjust the temperature
control to the lowest point and let it work till the temperature of inner cabinet
decreases to -18
℃
and then putting the stuff in, after 12 hours adjust the
temperature control to the normal point
.
•
Never put hot food in the showcase directly only after it has been cooled
naturally outside
.
•
The stuff should be put into the showcase partially, each lot will not be more
than the figure which is equal to the capacity(L) divide by 20.
•
Not full the showcase and make it crowded, big meat should be divided into
several small parts. There should be reason- able space between the foods for
better freezing.
•
If power cut off is needed, you should wait for at least 5 minutes before turn on
again to avoid damage to the com- pressor
.
•
The stuff stored should be packed with plastic bag well to avoid smell-mixed
and moisture
-los
t
, and r
educe the frost at the small time
.
•
Beer
, be
verage
, fr
esh flower
, medicine and in
jections can not be put into the
showcase
.
•
Please make the temperature control to the lowest point if you want to store ice
cream or other uneasy
-
frozen food.
•
We have a policy of continuous improvement on our prod- ucts and reserve the
right to change materials and specifica- tions without notice
. T
o confirm the
specific parameters
,
please accord to the rated label on the product
.
•
Shall, when the product scrap/recovered by professional scrap/recycling
locations to deal with.
•
This product application environment temperature up to 43°C
.
TRANSPORTATION AND INSTALLATION IN-
STRUCTIONS
1
When you transport the showcase
, the angle be
tween the compartment body
and the ground should be no more than 45° and you should never place the
showcase up
-
side down.
2
Do not use any of the external part as loading points
, f
or example
, the
c
ondenser on the back
, the door.
3
When the showcase is installed or used, all the package
(
including board and foam plastic) should be got rid of
.
4
Keeping the showcase stable to avoid vibration and noise
.
5
The showcase should be installed in the place with good ventilation, a space of
at least 10cm should be allowed between the surrounding walls and the
cabinet wall for air condition.
6.
It should be placed far from heating resource and not under direct sunshine to
avoid decrease of the efficiency of refrig- eration.
7.
Install the showcase in a dry place so as to prevent rust on the compartment
body
, which ma
y affect the electric insula- tion.
OPERATING YOUR SHOWCASE
THE FUNCTION OF CONTROL PANEL:
Mechanical Thermostat:
1
The figure on the temperature control 1~7 only means the temperature level
from high to low
, no
t means the specific temperature
, turn the knob
clockwise, the t
emperature inside will go down, turn the knob to the other
direction, the temperature will go up
.
2
The green light is a power indicator
, when it on , the po
wer is connected.
3
When you turn the knob anticlockwise to
“off”
or
“0”
the freezer will not be
supplied power
.
Do not turn the knob from “7” to “off” or “0”!
Electronic Thermostat:
1
The EMC is electronic controller.
2
If the control panel has a green light,it’s a power indicator, when it on,the power
in connected.
DEFROST:
1
Defrost when the frost thickness on the wall of the cabinet reaches 5mm to
optimize the freezing capacity
.
2
Turn the temperature control to the lowest point for 5-6 hours before
defrosting.
3
Cut off the power and take out the food, use the defrost removal, do not apply
sharp tools.
4
After defrosting
, cle
an the wall with dry cloth, and then power on.
THE FOLLOWING PHENOMENA ARE NORMAL:
1
There will be sound of flowing water when the refrigerant is running.
2
The frozen food do not melt even if a long time power off
.
3
When the environment humidity is too high, there will be dew condensed on
the surface of the showcase
.
4
When the machine is running
, the c
ondenser and compressor will be hot.
