Scan Optics SO-111-R Скачать руководство пользователя страница 20

Страница: 20 / 22

SO-111-R/RF Ophthalmic Microscope

User Manual

Page 20 of 22

Issue number 1.0 X:\Current User Manuals\SO-111-R-RF User Manual v1.0.doc

TROUBLESHOOTING

SYMPTOM

CAUSE

REMEDY

No lamp/failed lamp

Replace lamp

Mains power failure

Use battery back-up
Check and replace fuse if
necessary

No light

Fuse blown

Check mains voltage setting
110/220V

Incorrect voltage setting

Check mains voltage setting
110/220V

Fuse repeatedly blows

Mains power fault

Check mains wiring, do not
use microscope if wired
incorrectly. Use battery
backup

Intensity turned down

Increase intensity

Aged lamp

Replace lamp

Dirty optics

Clean eyepieces, prism and
objective lens

Battery power low

Recharge/replace battery

Incorrect lamp

Replace with lamp of correct
specification

Low light level

Lamphouse off-centre

Re-centre lamphouse on
image centre (use adjusting
grubscrews)

Microscope falls under own
weight

Insufficient focus friction

Increase focus friction

Connect foot control to
underside of power supply

No connection

Open focus cover and check
the connection inside the hole
in the black plastic block

Too much friction

Reduce focus friction

Foot controlled focus does
not function

Speed control too low

Increase focus speed

Blurred vision

Dirty optics

Clean eyepieces, prism and
objective lens

Mouldy optics

Carefully clean mould from
optical elements and replace
mould protection pellet

Refractive error

Focus right eye first through
RHS eyepiece then adjust
LHS eyepiece to compensate
for error

Microscope unsteady

Unstable surface

Stiffen mounting surface with
a plate

Knobs loose

Tighten adjustment knobs as
necessary

Содержание SO-111-R























Результаты поиска

Содержание SO-111-R

Отзывы:

Похожие инструкции для SO-111-R

Бренды по названию

Популярные бренды

Scan Optics SO-111-R, Руководство пользователя

Результаты поиска

Содержание SO-111-R

Отзывы:

Похожие инструкции для SO-111-R

Бренды по названию

Популярные бренды