background image

LIMITED WARRANTY - COMMERCIAL EqUIPMENT

Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment of Scag, to 
be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts 
and labor during the periods specified below. This warranty is limited to the original purchaser and is not transferable. Proof of purchase 
will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an Authorized Scag Service 
Dealer.

This warranty is limited to the following specified periods from the date of the original retail purchase for defects in materials or 
workmanship:

Wear items including drive belts, blades, hydraulic hoses and tires are warranted for ninety (90) days.

• 

Batteries are covered for ninety (90) days.

• 

Frame and structural components including oil reservoir and oil coolers are warranted for two (2) years (parts and labor) for 

• 

commercial use or three (3) years / 500 hours (whichever comes first) (parts and labor) for non-commercial use.

Cutter decks are warranted against cracking for a period of three (3) years. (parts and labor 1st and 2nd year; parts only 3rd 

• 

year.) The repair or replacement of the cutter deck will be at the option of Scag Power Equipment. We reserve the right to request 
components for evaluation. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or 
accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual.

Engines and electric starters are covered by the engine manufacturer’s warranty period.

• 

Major drive system components are warranted for two (2) years (parts and labor) for commercial use or three (3) year / 500 hour 

• 

(whichever comes first) (parts and labor) for non-commercial use by Scag Power Equipment. (commercial and non-commercial 
warranty excludes fittings, hoses, drive belts). The repair or replacement of the hydraulic pump or hydraulic motor will be at the 
option of Scag Power Equipment. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or 
accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual.

Electric clutches have a Limited Warranty for two (2) years (parts and labor) for commercial use or three (3) year / 500 hours 

• 

(whichever comes first) (parts and labor) for non-commercial use.

Spindle assemblies have a Limited Warranty for three years (parts and labor 1st year and 2nd; parts only 3rd year).

• 

Any Scag product used for rental purposes is covered by a 90 day warranty. 

• 

The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty period. The 
expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid 
for by the owner. Scag’s responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for 
cancellation or rescission of the contract of sale of any Scag mower. “Non-Commercial” use is defined as a single property owner, 
where the single property is the residence of the owner of the mower. If the mower is cutting more than the owners single property, it is 
deemed commercial use and the “non-commercial” warranty does not apply. Scag Power Equipment reserves the right to deny and / or 
void the non-commercial warranty if it believes it to be in commercial use.

This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been 
operated in any way contrary to the operating instructions as specified in the Operator’s Manual. 

The warranty does not apply 

to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have not been assembled or 
installed as specified in the Operator’s Manual and Assembly Manual. The warranty does not cover any mower that has been altered or 
modified, changing performance or durability. In addition, the warranty does not extend to repairs made necessary by normal wear, or 
by the use of parts or accessories which, in the reasonable judgment of Scag, are either incompatible with the Scag mower or adversely 
affect its operation, performance or durability.

Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obligation to 
modify any mower previously manufactured.

 All other implied warranties are limited in duration to the two (2) year for commercial 

use, three (3) years / 500 hour for non-commercial use or ninety (90) days for mowers used for rental purpose. Accordingly, any such 
implied warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the 
expiration of the appropriate two year or ninety day warranty period. Scag’s obligation under this warranty is strictly and exclusively 
limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them any other 
obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for gasoline, 
expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner, mechanic’s travel time, 
telephone or telegram charges, rental of a like product during the time warranty repairs are being performed, travel, loss or damage to 
personal property, loss of revenue, loss of use of the mower, loss of time or inconvenience. Some states do not allow the exclusion or 
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you 
specific legal rights, and you may also have other rights which vary from state to state.

Содержание Wildcat STWC48V-25CV



















































































Отзывы: