background image

6

R

Section 2

Lower the roll bar only when absolutely necessary.

To lower the roll bar, remove the hairpin cotter pins 

1. 

and remove the two (2) lock pins. See Figure 2-2.

Lower the roll bar to the down position.

2. 

To raise the roll bar, lift the bar to the upright 

3. 

position.

Install the two (2) lock pins through the hole, secure 

4. 

with the two (2) hairpin cotter pins. See Figure 2-2.

UPRIGHT AND
LOCKED POSITION

Foldable Roll-Over Protection System

Figure 2-1. 

HAIR PIN

LOCK PIN

ROPS Hinge

Figure 2-2. 

The potential exposure of the seat belt to severe 
environmental conditions make it crucial to inspect the seat 
belt system regularly.

It is recommended that the seat belt be inspected on a 
daily basis for signs of damage. Any seat belt system that 
shows cuts, fraying, extreme or unusual wear, significant 
discoloration due to UV exposure, dirt or stiffness, abrasion 
to the seat belt webbing, or damage to the buckle, latch 
plate, hardware or any other obvious problem should be 
replaced immediately.

Use care when approaching blind corners, shrubs, 

22. 

trees, or other objects that may obscure vision.

NEVER leave the machine running unattended.

23. 

ROLL-OVER PROTECTION SYSTEM

2.5 

 WARNING

Keep the roll bar in the raised and locked position 
and the seat belt securely fastened during 
operation. Failure to do so could cause serious 
injury or loss of life.

This mower has been designed for good traction and 
stability under normal mowing conditions. However, caution 
must be used when traveling on slopes, especially when the 
grass is wet. Do not mow on wet grass. Wet grass reduces 
traction and steering control.

Any or all parts of the Roll-Over Protection System MUST 
NOT be removed. Failure to adhere to this guideline could 
result in injury or death.

 WARNING

There is no roll-over protection when the roll bar 
is in the down position.

Lower the roll bar only when absolutely 
necessary.

Raise the roll bar as soon as clearance permits.

DO NOT wear the seat belt when the roll bar is in 
the down position.

ALWAYS wear seat belt when roll bar is in the up 
position.

Operate the machine smoothly, no sudden turns, 
starts or stops.

Check the area carefully before mowing for proper 
overhead clearance (i.e. branches, doorways, 
etc.).

DO NOT contact any overhead object with the 
roll bar.

Содержание Wildcat STWC48V-25CV



















































































Отзывы: