Scag Power Equipment SMTC-40 Скачать руководство пользователя

Страница: 17 / 66

Section 4

To stop the forward travel, pull the steering control levers

back to the neutral position.

To steer the mower left while traveling forward, pull the

left steering lever back. The further the lever is pulled

back, the quicker the mower will turn left.

To steer the mower right while traveling forward, pull the

right steering control lever back. The further the lever is

pulled back, the quicker the mower will turn right.

-NOTE-

Smooth operation of the steering levers will

produce smooth mower operation. While

learning the operation of the steering

controls, keep the travel speed low.

-IMPORTANT-

Do not travel forward over a curb. The

mower may hang up on the curb. Raise the

deck and travel backwards over the curb at a

45 degree angle. (see section 4.1, item 13 for

cutter deck raising instructions)

Reverse Travel

Disengage power to the mower before backing up.
Do not mow in reverse unless absolutely necessary
and then only after observation of the entire area
behind the mower.

Before backing up, observe the rear for persons
and obstructions. Clear the area before backing
up. Possible injury or property damage could occur.

To travel in reverse, pull levers inward out of the neutral

lock position and pull both handles back. Keep the travel

speed low while traveling in reverse.

-NOTE-

The mower may not travel straight in reverse.

Slight adjustments must be made using the

steering controls.

To steer left while traveling in reverse, allow the left

steering control lever to move forward. The futher the

control is allowed to move forward, the quicker the

mower will turn left.

To steer right while traveling in reverse, allow the right

steering control lever to move forward. The further the

control is allowed to move forward, the quicker the

mower will turn right.

To stop the reverse travel, allow the steering control

levers to return to the neutral position. If the mower is to

be parked, place the handles in the neutral lock position

and engage the parking brake.

4.6 ENGAGING THE DECK DRIVE (CUTTER
BLADES)

1. Set the throttle at about 3/4 speed. Do not attempt to

engage the deck drive at high speed as this shortens

the electric clutch life use only moderate engine

speed when engaging the deck drive.

2. Engage the deck drive by pulling out on the yellow

switch, located on the instrument panel, (Figure 4-3)

to the engage position.

CAUTION:

Figure 4-3 Cutter Engage Switch

STT99CES

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

Содержание SMTC-40



































































Результаты поиска

Содержание SMTC-40

Отзывы:

Похожие инструкции для SMTC-40

Бренды по названию

Популярные бренды

Scag Power Equipment SMTC-40, Руководство оператора

Результаты поиска

Содержание SMTC-40

Отзывы:

Похожие инструкции для SMTC-40

Бренды по названию

Популярные бренды