background image

1

4

3

2

4

3

SawStop

®

 Contractor Mobile Base

3

Installing Your Mobile Base

Mobile Base Hardware Pack

Nylon Hex Nuts, 

M6 (2)

4

Lock Washers, 

M8 x 13.6 (4)

6

Flange Lock Nuts,

M6 (2)

9

Shoulder Socket Screw, 

M8 x 17.7 (1)

15

Shoulder Socket Screw, 

M8 x 15.7 (1)

13

Nylon Hex Nut, 

M8 (1)

19

Cap Nut, 

M8 (1)

20

Extension Spring,

(1)

17

Hex Bolts, 

M8 x 40 (2)

8

Caster Nuts, 

3/8” thread (2)

12

Wave Washer, 

M10.5 x 14.5 (1)

16

Short Fixed Wheel Axle, 

M6 x 67.6 (1)

1

Long Fixed Wheel Axle, 

M6 x 73.8 (1)

2

Washers, 

M6 x 16 (4)

3

Button Head Socket 

Screws, M8 x 20 (4)

5

Washers, 

M8 x 18 (4)

7

Hex Screw, 

M8 x 30 (1)

14

Release Lever 

Locking Screw (1)

18

Lock Washers, 

M10.5 x 17 (2)

11

Washers, 

M10.5 x 25 (2)

10

Low

er

Raise

Never place fingers,

toes or other body parts

under the mobile base.

!

WARNING

1.  Nev

er plac

e finge

rs, toes

 or othe

r    

body p

arts un

der the

 mobile

 base.

2.  Alw

ays use

 the saw

 and th

e mobil

e

base o

n a leve

l surfac

e.

3.  Low

er the s

aw befo

re usin

g

 saw w

hen it is

 raised

 off 

4. Low

er the

saw slo

 

drop ba

ck to.

!

WARNIN

G

Installing Your Mobile Base

Fig. 1

Fig. 2

Fig. 3

1.  Locate all of the mobile base components shown on page 1. All of the hardware 

needed to install the mobile base is located on the mobile base hardware pack 

(see Fig. 1). In order to easily identify the hardware used in each of the following 

steps, the different pieces of hardware are numbered on the hardware pack and 

in the figures. If you are missing the hardware pack or any of the other mobile 

base components, call the SawStop Service Department at 503-582-9934 for 

replacements.

 

You will need the following tools to complete the mobile base installation:

 

• two 10 mm wrenches 

 

 

• two 13 mm wrench

 

• a 14 mm wrench

 

• a 5 mm hex key

Note:

 

The stand for your contractor saw must be fully assembled before installing the mobile base.

2. 

Take  the  wheel  support  and  mount  one  of  the  3 

inch wheels to the end furthest from the foot pedal.  

Use

 the short axle, one M6 washer, and one M6 

nylon hex nut to mount the wheel to the support 

as shown in Fig. 2. Fully tighten the nut using a 10 

mm wrench and a 5 mm hex key.

3.  Mount the other 3 inch wheel to the other end of the 

wheel support. Use

 the long axle, one M6 washer, 

and one M6 nylon hex nut to mount the wheel to 

the support as shown in Fig. 3. Do not tighten the 

nut because it will be removed in a later installation 

step.

foot pedal

3 inch 

wheel

3 inch 

wheel

foot pedal

Содержание MB-CNS-000













Отзывы: