manualshive.com logo in svg

SawStop ICS31230, Руководство пользователя

Поделиться
Скачать
SawStop ICS31230 Скачать руководство пользователя страница 59

SawStop

®

 10” Industrial Cabinet Saw    57

Adjusting 

Your 

Saw

Making Adjustments to Your Saw

Upper Elevation Limit Stop
To check the position of the upper elevation limit stop, install a 10 inch saw blade on the arbor (see page 17), 

and turn the elevation hand wheel clockwise until the limit stop is reached. Using a combination square or 

similar tool, measure the distance from the top of the table to the tip of the highest tooth on the blade. The 

maximum height of the blade above the table should be 3 

1

/

8

 inches. If the blade is 3 

3

/

16

 inches or higher 

above the table, the upper elevation limit stop should be adjusted downward. If the blade is less than 3 

1

/

8

 

inches above the table, you can adjust the limit stop upward to 3 

1

/

8

 inches. Alternatively, you can adjust the 

limit stop so that the maximum blade height is lower than 3 

1

/

8

 inches.

The upper elevation limit stop is set by the bolt mounted in the lower front portion of the elevation plate (see 

Fig. 68). You can access the upper limit bolt by opening the motor cover. The head of the bolt is painted 

yellow for easy identification. To adjust the 

position of the upper limit bolt, first loosen 

the  locking  nut  and  back  it  off  several 

turns. If you plan to adjust the limit stop 

upward, turn the bolt counter-clockwise 

several turns.

Next, set the blade elevation to the correct 

maximum height. Turn the upper limit bolt 

clockwise until it is tight. Finally, turn the 

locking nut clockwise until it is tight. The 

upper elevation limit stop has now been 

set.

4.  Adjusting the Elevation Limit Stops:

The upper elevation limit stop prevents the arbor block and belts from hitting the underside of the table. The 

lower elevation limit stop prevents the arbor block or blade from hitting the lower trunnion assembly. The 

elevation limit stops must be adjusted correctly to ensure proper operation of the saw.

WARNING!

 Always turn off the Main Power Switch and switch the Disconnect 

Switch to the OFF position before making any adjustments to your saw.

Fig. 68

upper elevation 

limit stop

lower elevation 

limit stop

Содержание ICS31230















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды