manualshive.com logo in svg

Savant CLI-W200, Быстрый старт, Страница: 11 / 12

Поделиться
Скачать
Savant CLI-W200 Скачать руководство пользователя страница 11

11

009-1593-02

Regulatory

FCC Interference Statement

FCC Caution

Any changes or modifications not expressly approved by the party responsible 

for compliance could void the user's authority to operate this equipment. This 

transmitter must not be co-located or operating in conjunction with any other 

antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for an 

uncontrolled environment. This equipment should be installed and operated 

with a minimum distance 20cm between the radiator & your body.

This device electronically displays the FCC declaration of conformity logo as 

well as the FCC and IC identifier. This information can be found on the device 

by accessing: 

HVAC Mode menu  

    Swipe Left 

  About.

This device complies with part 15 of the FCC Rules. Operation is subject to the 

following two conditions: 

1.  This device may not cause harmful interference, and

2.  This device must accept any interference received, including interferences that 

may cause undesired operation.
This equipment has been tested and found to comply with the limits for CLASS 

B digital device, pursuant to Part 15 of FCC Rules. These limits are designed 

to provide reasonable protection against harmful interference when the 

equipment is operated in a residential installation. This equipment generates, 

uses and can radiate radio frequency energy and, if not installed and used 

in accordance with the instructions, may cause harmful interference to radio 

communications, However, there is no guarantee that interference will not occur 

in a particular installation. If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try correct the interference by one 

or more of the following measures:

 

– Reorient or relocate the receiving antenna.

 

– Increase the separation between the equipment and the receiver

 

– Connect this equipment into an outlet on a circuit different from that to which 

the receiver is connected.

 

– Consult the dealer or experienced radio/TV technician for help.

The following statements are applicable to the CLI-W200x

FCC and IC Identifier for Savant Thermostat

Radiation Exposure Statement

Содержание CLI-W200













Отзывы:

Нет отзывов