manualshive.com logo in svg

Saunier Duval Themaclassic F24E PLUS, Инструкция по использованию, установке и обслуживанию

Поделиться
Скачать
Saunier Duval Themaclassic F24E PLUS Скачать руководство пользователя страница 50

50

4000121771-2

20 Replacement of Parts

20.26 Bypass valve, refer to diagram 20.15.

Before starting refer to the front of 

Section 20 Important

information.

• Remove the front panel

, refer to Section 17.3.

• Lower the control panel

, refer to Section 17.4.

Drain down the boiler, 

refer to relevant part of Section 20.1

.

Pull out slotted metal clip, ease out bypass valve from bypass
valve housing.

20.27 Automatic air vent, refer to diagram
20.16.

Before starting refer to the front of 

Section 20 Important

information.

• Remove the front panel

, refer to Section 17.3.

• Lower the control panel

, refer to Section 17.4.

• Drain down the boiler only, 

refer to relevant part of diagram

20.1

.

• Unscrew to remove automatic air vent.

• After fitting replacement automatic air vent ensure the cap is
open.

20.28 Gas Control valve, refer to diagram
20.17.

Before starting refer to the front of 

Section 20 Important

information.

• Remove the front panel

, refer to Section 17.3.

• Lower the control panel

, refer to Section 17.4.

• Disconnect gas supply pipes and union nuts at the gas control
valve.

• Disconnect supply pipe union nut at the burner injector bar.

• Remove gas control valve retaining clip from the underside of
gas control valve.

• Remove the locking nut and brass washer from underside of
gas control valve.

• Ease gas control valve forwards and disconnect electrical
connections to gas control valve.

Note:

 The washers must be kept for use on reassembly.

• Withdraw gas control valve assembly.

• Fit replacement gas control valve.

If the step pressure requires adjusting, refer to Section 15
Changing Gas Type.

20.29 Gas control valve stepper motor, refer to
diagram 20.18

Before starting refer to the front of 

Section 20 Important

information.

• Remove the front panel

, refer to Section 17.3.

• Lower the control panel

, refer to Section 17.4.

• 

Remove the gas control valve

, refer to Section 20.28.

• 

Disconnect the electrical connection from stepper motor.

• 

Remove the two screws securing stepper motor to the gas

control valve.

• Fit replacement gas control valve stepper motor.

• Note: Take care not to damage the 'O' ring.

➜

➜

9758

Diagram 20.15

SYSTEM WATER PRESSURE
SENSOR

BYPASS VALVE

9760

AIR VENT

CAP

9781

Diagram 20.17

GAS CONTROL
VALVE

➜

➜

➜

➜

➜

9782

11591

Diagram 20.16

Содержание Themaclassic F24E PLUS

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды