manualshive.com logo in svg

Saunier Duval Themaclassic F24E PLUS, Инструкция по использованию, установке и обслуживанию

Поделиться
Скачать
Saunier Duval Themaclassic F24E PLUS Скачать руководство пользователя страница 46

46

4000121771-2

20 Replacement of Parts

20.10 Burner injector assembly, refer to
diagram 20.5 and 20.6.

Before starting refer to the front of 

Section 20 Important

information.

• Remove the front panel

, refer to Section 17.3.

• Lower the control panel

, refer to Section 17.4.

• Remove the sealed chamber cover, 

refer to Section 17.5.

• Remove the combustion chamber cover, 

refer to Section17.7.

• Remove burner from boiler, 

refer to Section 17.9.

• Undo the gas supply union nut from under the sealed
chamber.

Note: The fibre washer between the burner injector assembly
and gas supply must be kept for use on reassembly.

•  Undo and remove the sense  and ignition electrode assemblies.

• Remove the burner injector assembly securing screws.

• Remove the burner injector assembly by lifting up, easing the
gas connection through the grommet in the sealing chamber.

Note: Take care not to damage the insulation.

• When refitting burner injector assembly ensure the gas
connection locates correctly through the grommet.

Note: Make sure that injector size, marked on each injector, is
the same as that given in ‘

Section 1 Technical Data

’ for the

type of gas being used.

20.11 Overheat thermostat

Before starting refer to the front of 

Section 20 Important

information.

• Remove the front panel

, refer to Section 17.3.

• 

Remove the sealed chamber cover

, refer to Section 17.5.

• Locate overheat thermostat on heating flow pipe on left hand
side of boiler, 

see part of diagram 20.7.

• Disconnect electrical connections from thermostat

• Remove the thermostat and bracket assembly from heating
flow pipe by unclipping at the side of the bracket. Remove the
thermostat, fit new thermostat and replace assembly.

• When refitting electrical connections to replacement
thermostat the polarity is not important.

20.12 Ignition electrode

Before starting refer to the front of 

Section 20 Important

information.

• Remove the front panel, 

refer to Section 17.3.

• Lower the control panel, 

refer to Section 17.4.

• 

Remove the sealed chamber cover, 

refer to Section 17.5.

• Remove the combustion chamber cover, 

refer to Section

17.7.

• Remove the burner, 

refer to Section 17.9.

• Remove the right hand side panel, 

refer to Section 17.6.

• Undo and remove screw securing electrode assembly  to the
burner injector assembly, 

see diagram 20.6.

• Disconnect the electrical connections at the ignition unit, 

see

diagram 20.22.

  Note the routing of the cables.

20.13 Flame sense electrode

Before starting refer to the front of 

Section 20 Important

information.

• Remove the front panel, 

refer to Section 17.3.

• Lower the control panel, 

refer to Section 17.4.

• 

Remove the sealed chamber cover, 

refer to Section 17.5.

• 

Remove the combustion chamber cover, 

refer to Section

17.7.

• Remove burner, 

refer to Section 17.9

.

• Remove the left hand side panel

, refer to Section 17.6.

• Undo and remove screw securing sense assembly to the
burner injector assembly

, see diagram 20.6.

• Disconnect the electrical connection from the inline connector

,

Note the routing of the cable.

Diagram 20.5

Diagram 20.6

BURNER INJECTOR
BAR

GAS SUPPLY
PIPE

GROMMET

IGNITION ELECTRODE
ASSEMBLY

SENSE ELECTRODE
ASSEMBLY

9813

9814

9819a

9820

Diagram 20.7

9749

PIPE
SECURING
CLIP 2 OFF

ELECTRICAL
LEADS

OVERHEAT
THERMOSTAT

HEAT EXCHANGER

9750

RESET
BUTTON

CLIP

Содержание Themaclassic F24E PLUS

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды