background image

11 

 

Specifications 
 

Name 

Jumbo LCD Digital Thermometer (K Type Thermocouple) 

Model

 

SK-1110 

Cat. No.

 

8014-03 

Number of channel

 

1 channel 

Measuring range 

-50 to 1300

º

Display range 

-73.3 to 1371.0

º

Accuracy 

(main body) 

±(0.5%rdg + 1) 

º

C at -50 to 0.0

º

±(0.3%rdg + 1) 

º

C at 0.1 to 1000

º

±(0.5%rdg + 1) 

º

C at 1001 to 1300

º

Resolution 

0.1

º

Sampling time 

about 0.5 sec. 

Operation ambient 

0 to 50

º

C for temperature, less than 80%RH for humidity no condensing 

Storage ambient 

-10 to 60

º

C for temperature, less than 70%RH for humidity no condensing

Power requirements 

9VDC (AAA manganese battery × 6) 

Battery life 

about 110 hours 

Sensors 

K Thermocouple, Connector: ANSI standard, yellow 

Dimensions 

(W) 72 × (H)151 × (D) 35 mm 

Materials ABS 

resin 

Weight 

approx. 240 g (including batteries) 

Functions 

MAX/ MIN: maximum/ minimum memory data 

HOLD: data hold 

AVG: average value 

Memory function (up to 150 data) 

Auto Power-off function (about 30 minutes) 

Auto Power-off function release 

OFFSET(REL): offset value 

Standard Accessories 

AAA manganese battery × 6, vinyl cover 

Содержание SK-1110

















Отзывы: