manualshive.com logo in svg

Sargent Passport 1000 PG, Руководство по установке, Страница: 8 / 28

Поделиться
Скачать
Sargent Passport 1000 PG Скачать руководство пользователя страница 8

Inside of door (Metal)  

Fig. 2B1  

ET Wire harness 

(from motor)  

Exit chassis  

(2) ¼ x 2-3/8”  

flat head         

machine screws 

(secures ET)  

Inside of door (Wood) 

Fig. 2B2     

(Wood Door)  

ET Wire harness  

(from motor)  

Exit chassis  

Ground harness (from motor, 

wood doors only)

Put ground lug 

through top flat 

head screw and 

tighten down

(2) 1/4 x 2-3/8”           

flat head machine 

screws (secures ET)  

ET control  

Outside of door  

ET 

gasket  

ET Wire harness 

(from motor)  

Fig. 2A  

Rim Installation Instructions (Continued)

 

2 – Installation of Exit Trim (ET), Exit Chassis and Cylinder 

B. Inside Trim 

1. Route “ET” harness along wire channel cutout for 

wood doors and access hole for metal doors. 

2. Mount exit chassis carefully. DO NOT PINCH 

HARNESS WIRES.  

3. “ET” spindle will engage into the hub of exit device 

chassis. 

4. Secure chassis and “ET” with (2) 1/4 -20 x 2-3/8” 

flat head machine screws.  

A. Outside Trim 

1. For exterior applications, “ET” gasket (52-0263) 

should be used to seal between “ET” escutcheon 
and outside door surface. 

2. Route harness through under cut of cylinder hole 

and out to other side of door. 

3. Place “ET” control onto door.  

10/31/12

A7809B                8

Copyright © 2012, Sargent Manufacturing Company

, an ASSA ABLOY Group company

. All rights reser

ved. 

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 PG Exit Device

Содержание Passport 1000 PG





























Отзывы:

Нет отзывов