manualshive.com logo in svg

Sargent Passport 1000 PG, Руководство по установке, Страница: 2 / 28

Поделиться
Скачать
Sargent Passport 1000 PG Скачать руководство пользователя страница 2

2 

      

   A8012E

Copyright © 2012, Sargent Manufacturing Company

, an ASSA ABLOY Group company

. All rights reser

ved. 

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

10/31/12

1

2

3

4

5

6

                         

Table of Contents

Warning  ........................................................................................ 2
General Description ...................................................................... 3
Hardware Specifications .............................................................. 3
Electronic Specifications .............................................................. 3
Part Breakdown ............................................................................ 4
Rim Type 8877/8878 Exit Device Installation .............................. 8
Mortise Type 8977/8978 Exit Device Installation ...................... 14
Setting up the 

PERSONA LockLink™ 

& Contact Card 

 ................... 20

Lockset Programming  ............................................................... 23
Operational Check ...................................................................... 27

8

7

Warning 

1

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfe-

rence in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio communications. However, there is 

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to correct the interference by one or more of the following measures:
• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

• 

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this unit not expressly approved by the party responsible 
for compliance could void the user’s authority to operate the equipment.

!

Observe precautions for handling electrostatic sensitive devices.

SARGENT Mfg. Co. Passport 1000 locksets utilizing a door position switch (DPS) are not rated for, 

or intended for use in life safety applications.

Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of 

the opening, and SARGENT Manufacturing makes no representations or warranties concerning what 

such impact may be in any specific situation.  When retrofitting any portion of an existing fire rated 

opening, or specifying and installing a new fire-rated opening, please consult with a code specialist 

or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes 

and ratings.

9

10

Industry Canada: 

Statement: The term “IC:” before the radio certification number only signifies that Industry Canada  

technical specifications were met.
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equip-

ment Regulations. Operation is subject to the following two conditions: (1) this device may not cause 

harmful interference, and (2) this device must accept any interference received, including interfe-

rence that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence cana-

dienne  

causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce  

dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle  

interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.

Содержание Passport 1000 PG





























Отзывы:

Нет отзывов