background image

English 

3

PRECAUTIONS

In case of problem

Do not use the camera if smoke or a strange odour comes 
from the unit, or if it seems not to function correctly. Disconnect 
the power cord immediately, and consult your dealer (or a 
Sanyo Authorized Service Centre).

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause 
damage to the unit. For internal settings and repairs, consult 
your dealer (or a Sanyo Authorized Service Centre).

Do not put objects inside the unit

Make sure that no metal objects or flammable substance get 
inside the camera. If used with a foreign object inside, it could 
cause a fire, short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the 
power cord immediately, and consult your dealer (or a Sanyo 
Authorized Service Centre). Be careful to protect the camera 
from rain, sea water, etc.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to 
strong shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric 
motor, transformer, audio speakers the magnetic field they 
generate will distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not install it where 
there is greasy smoke or steam, where the dampness may get 
too high, or where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat generating devices, 
such as spotlights, etc., or where it could be subject to direct 
sunlight, as that could cause deformation, discoloration or 
other damages.

Be careful when installing close to the ceiling, in a kitchen or 
boiler room, as the temperature may raise to high levels.

Install where the temperature range will stay between –10°C 
and 50°C. (no condensation)

Cleaning

• Dirt can be removed from the cabinet by wiping it with a soft 

cloth. To remove stains, wipe with a soft cloth moistened 
with a soft detergent solution and wrung dry, then wipe dry 
with dry soft cloth.

• Do not use benzine, thinner or other chemical product on 

the cabinet, as that may cause deformation and paint 
peeling. Before using a chemical cloth, make sure to read 
all accompanying instructions. Make sure that no plastic or 
rubber material comes in contact with the cabinet for a long 
period of time, as that may cause damage or paint peeling.

L5AF2_US.book  3 

ページ

  

2002年12月20日 金曜日 午後1時48分

Содержание VCC-3944 - 1/4" Color CCD DSP Camera





















Отзывы: