background image

Safety Guard

THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE
ACCOMPANYING THIS UNIT.

WARNING:

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK ,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.

This installation should be made by a qualified service person
and should conform to all local codes.

For the customers in Canada

This Class B digital apparatus complies with Canadian
ICES-003.

Pour la clientèle canadienne

Cet appareil numerique de la Classe B est conforme a la
norme NMB-003 du Canada.

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.

These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.

However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by 

Sanyo

may void the user’s authority to operate this camera.

2

 English

INFORMATIN TO USER

L5AF2_US.book  2 

ページ

  

2002年12月20日 金曜日 午後1時48分

Содержание VCC-3944 - 1/4" Color CCD DSP Camera





















Отзывы: