Sanyo SHP-C90GDN Скачать руководство пользователя страница 55

Страница: 55 / 76

− 55 −

Our advice to installer

• The installation work must be done correctly in order to derive the maximum from the product’s functions and

performance and to ensure safety. Prior to proceeding with the installation, read through the section entitled
“ IMPORTANT ! ”.

• Upon completion of installation, be absolutely sure to hand over the warranty and installation instructions to

the customer and ask that they be kept in a safe place.

• We will not be responsible for any accidents, failures or malfunctioning if the product has been installed

according to any methods which are not described in these instructions or in a manner which is not
consistent with the terms and conditions of the warranty or if the product has been installed without using
the designated optional parts.

• Noise will be heard from this product while it is operating. Do not install it where operating noise and vibration

will be a nuisance.

• The product’s performance cannot be guaranteed at locations where the minimum temperatures is –15

C or

below.

• Since the temperature of the water will drop, you must install additional heat insulating materials (and also

joints) to ensure that the product will be kept warm.

Installation procedure

1. Selecting the installation location and restrictions on installation

Page 5

2. Installing the heat pump unit

Page 7

3. Piping work

Page 8

4. Electrical work

Page 9

Post-installation inspections (checklist)

Page 13

5. Preparing for operation

Page 12

6. Instructions for the customer

Page 12

Installation Instructions

SHP-C90GDN
SHP-C90GEN

(heat pump unit)

For natural refrigerant
heat pump water heater

85264190461002

Содержание SHP-C90GDN












































































Результаты поиска

Содержание SHP-C90GDN

Отзывы:

Похожие инструкции для SHP-C90GDN

Бренды по названию

Популярные бренды

Sanyo SHP-C90GDN, Техническое руководство

Результаты поиска

Содержание SHP-C90GDN

Отзывы:

Похожие инструкции для SHP-C90GDN

Бренды по названию

Популярные бренды